Dell M4600 Uživatelský manuál

Dell™ Precision™ M4600 Owner's ManualRegulatory Model P13FRegulatory Type P13F001

NOTE: The color of your computer and certain components may appear differentlythan shown in this document.To avoid damaging your computer, perform the

Installing The Non-Touchscreen Display Bezel1. Place the display bezel on the computer.2. Starting from the bottom edge, press downward on the display

Display Panel 32Removing The Non-Touchscreen Display Panel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove

7. Peel back the adhesives and disconnect the low-voltage differentialsignaling (LVDS) cable from the back of the display panel.8. Remove the display

10. Remove the display bracket.Installing The Non-Touchscreen Display Panel1. Align the display bracket with the display panel and tighten the screwss

104

Camera 33Removing The Camera1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the standard display bezel or t

Installing The Camera1. Place the camera and microphone module on the display cover and tightenthe screw securing the camera and microphone module in

Display Hinge Cap Tower 34Removing The Display Hinge Cap Tower1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Rem

14. Remove the display hinges.15. Release the display hinge towers from the cables and remove the hingetowers.108

Installing The Display Hinge Cap Tower1. Insert the display hinge towers with the open end facing inward and ensurethe cables and antennas are not pin

• #0 Phillips screwdriver• #1 Phillips screwdriver• Small plastic scribe• Flash BIOS update program CDTurning Off Your ComputerCAUTION: To avoid losin

110

Low-Voltage Differential Signaling(LVDS) Camera Cable 35Removing The Low-Voltage Differential Signaling (LVDS) Camera Cable1. Follow the procedures in

Installing The Low-Voltage Differential Signaling (LVDS) Camera Cable1. Secure the low-voltage differential signaling (LVDS) cable to its routingchann

cover and remove the LVDS cable.113

Installing The RGB Low-Voltage Differential Signaling (LVDS) Cable1. Place the low-voltage differential signaling (LVDS) cable on the displaycover.2.

15. Pry up the camera cable from the display cover and remove the cameracable.115

Installing The RGB Camera Cable1. Place the camera cable on the display cover.2. Replace the adhesives to secure the camera cable in place.3. Connect

Specifications 36Technical SpecificationsNOTE: Offerings may vary by region. For more information regarding theconfiguration of your computer, click S

VideoType discreteData bus integrated videoVideo controller andmemory:M4600• AMD FirePro M5950 Mobility Pro Graphics with 1 GBGDDR5• NVIDIA Quadro 100

System InformationInterrupt Levels Integrated I/O APIC capability with 24interruptsBIOS Chip (NVRAM) 8 Mb (256 KB)Expansion BusBus Type PCI 2.3, PCI E

CAUTION: To connect a network cable, first plug the cable into the network deviceand then plug it into the computer.3. Replace the battery.4. Connect

Battery365 g (0.80 lb) (6–cell)500 g (1.10 lb) (9–cell / 9–cell LCL)Voltage 11.10 VTemperature range:Operating 0 °C to 35 °C (32 °F to 95 °F)Non-opera

Contactless Smart CardISO15693HID iClassFIPS201NXP DesfirePhysical M4600 M6600Height 36.5 mm (1.44 inches) 37.20 mm (1.46 inches)Width 376 mm (14.80 i

EnvironmentalAirborne contaminant level G1 or lower as defined by ANSI/ISA-S71.04-1985122

System Setup 37System Setup OverviewSystem Setup allows you to:• change the system configuration information after you add, change, orremove any hardw

Option DescriptionSystem Information This section lists the primary hardwarefeatures of your computer.• System Information• Memory Information• Proces

Option Description• Disabled• Enabled• Enabled w/PXEDefault Setting: Enabled w/PXESystem Management Allows you to control the systemsmanagement mechan

Option DescriptionNOTE: SATA is configured to supportRAID mode.USB Controller Allows you to control the USB controller.The options are:• Enable Boot S

Option Description• SATA-0• SATA-1• SATA-4• SATA-5Default Setting: All drives are enabled.VideoThe following table describe the menu options of the Vi

Option DescriptionSystem Password Allows you to set, change, or delete thesystem password.NOTE: Successful password changestake effect immediately.Def

Option DescriptionTPM Security Allows you to enable the Trusted PlatformModule (TPM) during POST.Default Setting: DisabledComputrace Allows you to act

Secure Digital (SD) Card 2Removing The Secure Digital (SD) Card1. Follow the procedures in Before Working On Your Computer2. Press in the Secure Digit

Option DescriptionMulti Core Support Allows you to enable or disable multi-coresupport for the processor. The options are:• All• 1• 2Default Setting:

Option DescriptionAuto On Time Allows you to set the time at which thecomputer must turn on automatically. Theoptions are:• Disabled• Every Day• Weekd

Option Description• LAN Only — Allows the system to bepowered on by special LAN signals.• WLAN Only — Allows the system to bepowered on by special WLA

Option DescriptionDefault Setting: Touchpad/PS-2 MouseNumlock Enable Allows you to enable the Numlock optionwhen the computer boots.Default Setting: E

Option Descriptionutilize the additional hardware capabilitiesprovided by Intel Trusted ExecutionTechnology. The TPM VirtualizationTechnology and Virt

Option DescriptionBIOS Events Allows you to view and clear the SystemSetup (BIOS) POST events.DellDiag Events Allows you to view and clear the DellDia

136

Diagnostics 38Device Status LightsTurns on when you turn on the computer and blinks when the computer is in apower management mode.Turns on when the c

Device Status LightsTurns on when you turn on the computerand blinks when the computer is in apower management mode.Turns on when the computer reads o

Diagnostic LED Error DescriptionBlinkingSolid Solid The microcontroller is handing control of thesystem to the processor. This code persists if noproc

14

140

Contacting Dell 39Contacting DellTo contact Dell for sales, technical support, or customer service issues:1. Visit support.dell.com.2. Verify your cou

ExpressCard 3Removing The ExpressCard1. Follow the procedures in Before Working On Your Computer.2. Press in on the ExpressCard gently to release it f

16

Battery 4Removing The Battery1. Follow the procedures in Before Working On Your Computer.2. Slide the battery release latch into the unlock position.3

18

Subscriber Identity Module (SIM)Card 5Removing The Subscriber Identity Module (SIM) Card1. Follow the procedures in Before Working On Your Computer.2.

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of yourcomputer.CAUTION: A CAUTION indicates

Installing The Subscriber Identity Module (SIM) Card1. Locate the Subscriber Identity Module (SIM) card slot in the batterycompartment.2. Push the SIM

Bluetooth Card 6Removing The Bluetooth Card1. Follow the procedures in Before Working On Your Computer2. Remove the Battery.3. Slide the Bluetooth doo

6. Remove the Bluetooth card.Installing The Bluetooth Card1. Place the Bluetooth card on the Bluetooth door and align with the screwhole.2. Tighten th

Base Cover 7Removing The Base Cover1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Remove the screws that secure

Installing The Base Cover1. Slide the bottom door downwards and towards the front of the system.2. Tighten the screws that secure the base cover to th

Keyboard Trim 8Removing The Keyboard Trim1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Using a plastic scribe,

Installing The Keyboard Trim1. Align the keyboard trim with the tabs on the top of the palm rest.2. Press downwards along the bottom edge to latch on

Keyboard 9Removing The Keyboard1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Remove the Keyboard trim.4. Remove

7. Remove the keyboard.8. Peel back the adhesive tape securing the keyboard data cable to the backof the keyboard.9. Disconnect the keyboard data cabl

10. Peel the keyboard data cable away from the keyboard and remove.Installing The Keyboard1. Connect the keyboard data cable to the back of the keyboa

ContentsNotes, Cautions, and Warnings...21 Working on Your Computer...

30

Optical Drive 10Removing The Optical Drive1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base cover.4

7. Remove the optical drive bracket from the drive.Installing The Optical Drive1. Tighten the screws to secure the bracket to the back of the optical

Hard Drive 11Removing The Hard Drive1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Remove the Base Cover.4. Remo

7. Remove the hard drive bracket from the system.8. Flex the hard drive bracket outward and press the hard drive upwards fromthe bottom.9. Remove the

Installing The Hard Drive1. Align the hard drive to the hard drive bracket.2. Slide the hard drive into the hard drive bracket.3. Slide the hard drive

36

Wireless Local Area Network(WLAN) Card 12Removing The Wireless Local Area Network (WLAN) Card1. Follow the procedures in Before Working On Your Comput

Installing The Wireless Local Area Network (WLAN) Card1. Slide the WLAN card into its slot.2. Tighten the single screw securing the WLAN card in place

Wireless Wide Area Network(WWAN) Card 13Removing The Wireless Wide Area Network (WWAN) Card1. Follow the procedures in Before Working On Your Computer

Installing The Base Cover...248 Keyboard Trim...

Installing The Wireless Wide Area Network (WWAN) Card1. Slide the Wireless Wide Area Network (WWAN) card into its slot.2. Tighten the screw securing t

Primary Memory 14Removing The Primary Memory1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Remove the Base Cover

Installing The Primary Memory1. Locate the memory slot in the system.2. Insert the memory into the memory socket.3. Press down on the memory module un

Secondary Memory 15Removing The Secondary Memory1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Remove the Keyboa

8. Remove the memory module from the computer.Installing The Secondary Memory1. Locate the memory slot in the system.2. Insert the memory module into

CPU Fan 16Removing The CPU Fan1. Follow the procedures in Before Working On Your Computer.2. Remove the Battery.3. Remove the Base Cover.4. Disconnect

Installing The CPU Fan1. Locate the CPU fan compartment in the system.2. Tighten the screws securing the CPU fan in place.3. Connect the CPU fan cable

Graphics Card Fan 17Removing The Graphics Card Fan1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base

Installing The Graphics Card Fan1. Locate the graphics card fan compartment in the system.2. Tighten the two screws securing the graphics card fan in

Coin-Cell Battery 18Removing The Coin—Cell Battery1. Follow the procedures in Before Working On Your Computer2. Remove the Battery.3. Remove the Base

16 CPU Fan...45Removing The CPU Fan...

Installing The Coin—Cell Battery1. Attach the coin— cell battery to the coin cell compartment.2. Connect the coin— cell battery to the system board.3.

Palm Rest 19Removing The Palm Rest1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove the base cover.4. Remove

11. Loosen the captive screws.12. Disconnect the speaker cable.13. Disconnect the media board cable.52

14. Disconnect the touchpad cable.15. Disconnect the Radio Frequency Identification (RFID) cable.16. Disconnect the fingerprint reader cable.53

17. Disconnect the power button cable.18. Lift up the left edge of the palm rest assembly.19. Release the tabs along the edges of the palmrest.54

20. Remove the palm rest.55

Installing The Palm Rest1. Align the two metal anchors at the bottom edge of the palm rest to theanchor hooks on the system.2. Starting from the right

CPU and Heatsink 20Removing The CPU Heatsink1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base cover

Installing The CPU Heatsink1. Locate the heatsink compartment on the system.2. Tighten the captive screws (1 > 2 > 3). Ensure the heatsink is pr

Processor 21Removing The Processor1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base cover.4. Remove

Installing The ExpressCard Module...6825 Input/Output Board...

Installing The Processor1. Insert the processor into the processor socket. Ensure the processor isproperly seated.2. Tighten the cam lock in a clockwi

Graphics Card Heatsink 22Removing The Graphics Card Heatsink1. Follow the procedures in Before Working On Your Computer2. Remove the battery.3. Remove

13. Loosen the four captive screws (1 > 2 > 3 > 4) on the heatsink.14. Lift up the graphics card heatsink and remove from the system.62

Installing The Graphics Card Heatsink1. Locate the heatsink compartment on the computer.2. Tighten the captive screws (1 > 2 > 3). Ensure the he

64

Graphics Card 23Removing The Graphics Card1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base cover.4

Installing The Graphics Card1. Locate the graphics card slot on the system.2. Tighten the screws securing the graphics card in place.3. Install the gr

ExpressCard Module 24Removing The ExpressCard Module1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the ba

11. Remove the ExpressCard module.Installing The ExpressCard Module1. Place the ExpressCard module in the system and tighten the three screwssecuring

Input/Output Board 25Removing The Input/Output Board1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the ba

33 Camera...105Removing The Camera...

11. Lift the right edge of the I/O board upwards to disengage the connector andremove from the system.Installing The Input/Output Board1. Place the In

DC-in Jack 26Removing The DC-in Jack1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base cover.4. Remo

20. Remove the DC-in jack.72

Installing The DC-in Jack1. Place the DC-in jack in the system.2. Place the DC-in bracket in the system and tighten the single screwsecuring it in pla

74

Display Assembly 27Removing The Display Assembly1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove the base c

11. Remove the screws at the bottom of the computer.12. Remove the two screws at the rear of the computer.13. Pull the antennas through the opening to

14. Loosen the captive screws securing the Low-voltage Differential Signaling(LVDS) cable in place.15. Disconnect the LVDS cable.16. Disconnect the ca

17. Remove the screws securing the display assembly in place.18. Remove the display assembly.78

Installing The Display Assembly1. Attach the display assembly to the base of the computer.2. Tighten the screws on the display assembly securing it in

8

80

System Board 28Removing The System Board1. Follow the procedures in Before Working On Your Computer.2. Remove the Secure Digital (SD) card.3. Remove t

23. Disconnect the Bluetooth cable on the top side of the system board.24. Disconnect the wireless switch cable.25. Remove the screws securing the hin

26. Remove the hinge cover.27. Remove the screws securing the system board in place.28. Gently lift the bottom edge of the system board assembly and r

29. Disconnect the DC-in cable.30. Remove the system board.84

Installing The System Board1. Align the system board to the port connectors on the rear of the chassisand place the system board in the computer.2. Ti

86

Touchscreen Display Bezel 29Removing The Touchscreen Display Bezel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3.

6. Pry up the left edge of the display bezel.7. Pry up the bottom edge of the display bezel.8. Work your way around the right edge of the display beze

9. Remove the display bezel.Installing The Touchscreen Display Bezel1. Place the display bezel on the computer.2. Starting from the bottom edge, press

Working on Your Computer 1Before Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potentialdamage an

90

Touchscreen Display Panel 30Removing The RGB Display Panel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Remove

7. Peel back the adhesives and disconnect the low-voltage differentialsignaling (LVDS) cable from the back of the display panel.8. Peel back the adhes

10. Remove the screws securing the display bracket to the display panel.11. Remove the display bracket.93

Installing the RGB Display Panel1. Align the display bracket with the display panel and tighten the screwssecuring the display bracket in place.2. Con

5. Remove the screws on the right side securing the display panel in place.6. Flip over the display panel.7. Peel back the adhesives and disconnect th

8. Disconnect the digitizer cable.9. Remove the screws securing the digitizer in place.10. Remove the touchscreen display panel.96

11. Remove the screws securing the display bracket to the display panel.12. Remove the display bracket.97

Installing The Touchscreen Display Panel1. Align the display bracket with the display panel and tighten the four screwssecuring the display bracket in

Display Bezel 31Removing The Non-Touchscreen Display Bezel1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Careful