Dell R220 Uživatelský manuál

Dell PowerEdge R220Owner's ManualRegulatory Model: E10SRegulatory Type: E10S003

Item Indicator, Button, or ConnectorIcon Descriptionwithin a rack. When one of these buttons is pressed, the system status indicator on the back flash

NOTE: For all PowerEdge and PowerVault documentation, go to dell.com/support/manuals and enter the system Service Tag to get your system documentation

12

2Using The System Setup And Boot ManagerSystem Setup enables you to manage your system hardware and specify BIOS-level options.The following keystroke

Choosing The System Boot ModeSystem Setup enables you to specify the boot mode for installing your operating system:• BIOS boot mode (the default) is

Keystroke ActionNOTE: For the standard graphics browser only.<Esc> Moves to the previous page till you view the main screen. Pressing <Esc>

Menu Item DescriptionSystem Security Displays options to configure the system security settings like, system password, setup password, TPM security, a

Processor Settings ScreenMenu Item DescriptionLogical Processor Allows you to enable or disable logical processors and display the number of logical p

Menu Item DescriptionPort A Auto enables BIOS support for the device attached to SATA port A. By default, Port A is set to Auto.Port B Auto enables BI

Menu Item DescriptionEmbedded NIC1 and NIC2Allows you to enable or disable the embedded network interface cards 1 and 2. By default, the Integrated Ne

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

Menu Item Descriptionattempt fails and the value must not be changed. By default, the Failsafe Baud Rate option is set to 115200.Remote Terminal TypeA

Menu Item DescriptionPassword Status Allows you to lock the system password. By default, the Password Status option is set to Unlocked.TPM Security Al

Menu Item DescriptionNOTE: This field does not apply to 84-key keyboards.Report Keyboard ErrorsAllows you to set whether keyboard-related error messag

5. Select System Password, enter your system password, and press <Enter> or <Tab>.Use the following guidelines to assign the system passwo

If an incorrect system password is entered, the system displays a message and prompts you to re-enter your password. You have three attempts to enter

Keystroke DescriptionDown arrow Moves to the next field.<Enter> Allows you to type in a value in the selected field (if applicable) or follow th

Embedded System ManagementThe Dell Lifecycle Controller provides advanced embedded systems management throughout the server’s lifecycle. The Lifecycle

3Installing System ComponentsRecommended ToolsYou may need the following items to perform the procedures in this section:• Key to the system keylock•

4. Unhook the right end of the bezel and pull the bezel away from the system.Opening And Closing The SystemWARNING: Opening the system or removing the

Closing The System1. Place the cover onto the chassis and offset it slightly toward the back of the system so that it aligns with the notches and lays

Contents1 About Your System...7Front-Panel Features A

NOTE: To install a 3.5-inch hard drive, install a 3.5 inch HDD0 hard-drive cage and to install a 2.5–inch hard drive, install a 2.5 inch HDD0/1 hard-d

Installing The Chassis Intrusion SwitchCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooti

9. If applicable, install the front bezel.Figure 8. Removing and Installing the Optical Drive1. data cable 2. power cable3. optical drive 4. metal sta

4. To remove the optical-drive blank, pull the optical-drive blank away from the system.5. Press down on the release latch and place the optical drive

NOTE: The procedure for removing a 3.5 inch HDD0 and HDD1 cage is identical.1. If installed, remove the front bezel.2. Turn off the system and attache

Installing A 3.5 Inch Hard-Drive CageCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting

Removing A 3.5 Inch Hard Drive From The Hard-Drive CageCAUTION: Many repairs may only be done by a certified service technician. You should only perfo

Removing A 2.5 Inch Hard-Drive CageCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting a

Installing A 2.5 Inch Hard-Drive CageCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting

Removing A 2.5 Inch Hard Drive From The Hard-Drive Cage1. Remove the screws from the side of the hard-drive cage.2. Remove the hard drive from the har

Removing A 2.5 Inch Hard-Drive Cage... 37Installing A 2.5 Inch Ha

LED ModuleRemoving The LED ModuleCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

Installing The LED ModuleCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple

8. Slide the control-panel board toward the back of the system and lift it out of the chassis.Figure 14. Removing and Installing the Control-Panel Boa

Cooling FansYour system supports three cooling fans.NOTE: Install fan 3 if you are installing an expansion card.NOTE: In the event of a problem with a

6. Install the cooling shroud.Figure 15. Removing and Installing a Cooling Fan1. cooling fans (3) 2. fan power cable connector3. cooling-fan bracket 4

9. Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.Cooling ShroudRemoving The Cooling ShroudC

Installing The Cooling ShroudCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and sim

channel 1: memory sockets 1 and 3channel 2: memory sockets 2 and 4The following table shows the memory populations and operating frequencies for the s

System Capacity (in GB)DIMM Size (in GB)Number of DIMMsDIMM Rank, Organization, and FrequencyDIMM Slot Population16 4 4 2R, x4, 1333 MT/s, 1, 2, 3, 42

9. Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.Figure 18. Removing the Memory Module1. me

Removing The System Board...63Installing The Syst

10. Close the system.11. Reconnect the system to the electrical outlet and turn on the system, including any attached peripherals.12. Press <F2>

Removing And Installing The Internal USB KeyCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubles

Expansion Card Types And Form FactorThe following table describes the types of expansions cards and the form factor:Table 2. Expansion Card Types and

8. Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.Figure 21. Removing and Installing the Exp

13. Install any device drivers required for the card as described in the documentation for the card.Removing The Expansion-Card RiserCAUTION: Many rep

Installing The Expansion-Card RiserCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting a

12. Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.Figure 23. Removing and Installing the iD

System BatteryReplacing The System BatteryWARNING: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery on

ProcessorRemoving The ProcessorCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and s

8. Lift the heat sink away from the processor and set the heat sink aside.Figure 25. Removing and Installing the Processor Heat Sink1. retention screw

Alert Messages... 969

11. Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.Figure 26. Removing and Inst

4. Remove the cooling shroud.WARNING: The heat sink and processor are hot to the touch for some time after the system has been powered down. Allow the

Removing The Power Supply UnitCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and si

Installing The Power Supply1. Open the system.2. Orient the power supply so that the connector fits through the back-panel opening.3. Align the screw

6. Remove the screws on the system board and slide the system board toward the front of the system.CAUTION: Do not lift the system board assembly by g

4. Install the screws that secure the system board to the chassis.NOTE: The cooling shroud retention screws cannot be interchangeably used with the ot

66

4Troubleshooting Your SystemSafety First—For You And Your SystemCAUTION: Many repairs may only be done by a certified service technician. You should o

5. If the problem is resolved, replace the faulty keyboard/mouse.6. If the problem is not resolved, proceed to the next step to begin troubleshooting

Troubleshooting A Wet SystemCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simp

1About Your SystemFront-Panel Features And IndicatorsFigure 1. Front-Panel Features and IndicatorsItem Indicator, Button, or ConnectorIcon Description

3. Ensure that the following components are properly installed:• Cooling shroud• Expansion-card risers (if present)• Expansion cards• Power supply(s)•

Troubleshooting The Power SupplyCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

Troubleshooting System MemoryCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and sim

Troubleshooting An Internal USB KeyCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting a

9. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.10. Enter the System Setup and ensure that

4. Reboot the system and enter the System Setup.5. Verify that the controller is enabled and the drives are displayed in the System Setup.If the probl

5. Close the system.6. Run the appropriate diagnostic test. For more information, see Using System Diagnostics.If a problem is still indicated, see Ge

5Using System DiagnosticsIf you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The

Menu DescriptionSystem Health Provides the current overview of the system performance.Event Log Displays a time-stamped log of the results of all test

6Jumpers And ConnectorsSystem Board Jumper SettingsFor information on resetting the password jumper to disable a password, see Disabling A Forgotten P

Item Indicator, Button, or ConnectorIcon Description5 Hard-drive indicatorThe indicator blinks green to indicate hard-drive activity.6 Electrical indi

System Board ConnectorsFigure 29. System Board Jumpers and ConnectorsItem Connector Description1 POWER CONN Power connector2 2, 4, 1 ,3 Memory module

Item Connector Description16 PWRD_EN Password enable jumper17 ODD/SATA_E ODD/SATA connector E18 CPU Processor19 FAN1 Cooling fan 1 connector20 POWER_1

82

7Technical SpecificationsProcessorProcessor type Intel Core i3-4130 and Core i3-4330 processorproduct familyIntel Pentium processor G3430 and G3420Int

ConnectorsSerial 9-pin, DTE, 16550-compatibleUSB Two 4-pin, USB 3.0-compliantVideo 15-pin VGAFrontUSB Two 4-pin, USB 2.0-compliantVideo 15-pin VGAInte

EnvironmentalSix consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 32 G fair

86

8System MessagesSystem Error MessagesSystem error messages appear on the monitor to notify you of a possible problem with the system. These messages r

Error Code Message InformationDetails The operating system or an application failed to communicate within the time-out period. The system was power-cy

Error Code Message InformationCPU0023Message CPU <number> is absent.Action Verify processor installation. If present, re-seat the processor.CPU

Item Indicator, Button, or ConnectorIcon Description10 USB connectors (2) Allow you to connect USB devices to the system. The ports are USB 2.0-compli

Error Code Message InformationAction1. Check system and operating system logs for exceptions. If no exceptions are found, continue. 2. Turn off the s

Error Code Message InformationAction Remove and reinstall the fan. If the issue persists, see Getting Help.HWC1001Message The <name> is absent.D

Error Code Message InformationDetails The memory may not be seated correctly, misconfigured, or has failed. Memory size is reduced.Action Check the me

Error Code Message InformationDetails System performance may be degraded. The device has failed to respond to a transaction.Action Cycle input power,

Error Code Message InformationPCI1360Message A bus fatal error was detected on a component at slot <number>.Details System performance may be de

Error Code Message InformationDetails The chassis was opened while the power was off. System security may have been compromised.Action Close the chass

Error Code Message InformationDetails Ambient air temperature is too cool.Action Check the system operating environment.TMP0120Message The system inle

9Getting HelpContacting DellNOTE: Dell provides several online and telephone-based support and service options. If you do not have an active Internet

98