Dell PowerVault MD3820f Uživatelský manuál

Dell PowerVault MD3800f and MD3820f Storage ArraysOwner's ManualRegulatory Model: E03J and E04J SeriesRegulatory Type: E03J001 and E04J001

Back-Panel Features and IndicatorsFigure 4. Back-Panel Features and Indicators—Dell PowerVault MD3800f and MD3820f Series1. 600 W power supply/cooling

Drive-Status Indicator Pattern (RAID Only)ConditionBlinks green, amber, and turns offPredicted drive failureBlinks amber four times per secondDrive fa

Item LED Type Icon DescriptionIf this LED is off, it indicates that the DC output voltage are not within the limit.2 Power supply/cooling fan faultThe

2Controller ModulesRAID Controller ModulesThe RAID controller modules provide high-performance, advanced virtual disk configuration, and fault-toleran

Item Component Function1 16 Gbps FC IN port (4) Provides host-to-controller FC connection.2 Seven segment display sequence Displays status or error co

RAID Controller Module—Additional FeaturesBattery Backup UnitEach RAID controller contains a two-cell Lithium ion nanopolymer battery backup unit (BBU

Write-Back CacheIn write-back cache, write operations result in a completion signal being sent to the host operating system as soon as the cache recei

Figure 9. SAS Cable1. mini SAS connector 2. SAS cable3. mini SAS HD connector Interoperability of 4 Gbps, 8 Gbps, and 16 Gbps DevicesThe FC standard s

18

3Installing Array ComponentsRecommended ToolsYou may need the following items to perform the procedures in this section:• Key to the system keylock• #

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

3. Secure the bezel with the keylock.Physical DrivesSAFETY Models AMT E03J and E04JModels AMT, E03J, and E04J are intended for installation only in re

Figure 12. Removing and Installing a 3.5 Inch Hard-Drive Blank (MD3800f only)1. physical-drive blank 2. release buttonInstalling a 3.5 Inch Physical-D

Figure 13. Removing and Installing a Hot-Swap Physical Drive1. release button 2. physical drive3. physical-drive carrier handleInstalling a Hot-Swap P

Removing a Physical Drive From a Physical-Drive Carrier1. Remove the screws from the slide rails on the physical-drive carrier.2. Lift the physical dr

Figure 15. Removing and Installing a 3.5 Inch Physical Drive Into a Physical-Drive Carrier1. physical-drive carrier 2. physical drive3. screws (4)Inst

CAUTION: RAID controller modules can be removed and installed without turning off the array. It is recommended that you do not remove the RAID control

CAUTION: If your configuration uses fiber-optic cables, remember that they are fragile. Bending, twisting, folding, or pinching fiber-optic cables can

CAUTION: Many repairs may only be done by a certified service technician. You must only perform troubleshooting and simple repairs as authorized in yo

Closing the RAID Controller ModuleCAUTION: Many repairs may only be done by a certified service technician. You must only perform troubleshooting and

6. Slide the backup battery unit and lift it out of the RAID controller module.Figure 19. Removing and Installing the RAID Controller Module Backup Ba

Contents1 About Your System...7Introduction...

Removing a Power Supply/Cooling Fan ModuleCAUTION: Many repairs may only be done by a certified service technician. You must only perform troubleshoot

Installing a Power Supply/Cooling Fan ModuleCAUTION: Many repairs may only be done by a certified service technician. You must only perform troublesho

4. Slide the control panel out of the chassis after:– Pushing the release tab toward the front of the array in PowerVault MD3800f.– Pulling the releas

3. Replace the hard drives in their respective slots.4. Connect all the power cables to the array.5. Turn on the array and the host server.BackplaneRe

11. Remove the screws that secure the backplane and pull the backplane out of the array.Figure 24. Removing and Installing the RAID Controller Module/

Figure 26. Removing and Installing the Backplane—PowerVault MD3820f1. screws (4) 2. backplane3. captive screwInstalling the Backplane1. Align the scre

36

4Troubleshooting Your SystemSafety First—For You and Your SystemCAUTION: Many repairs may only be done by a certified service technician. You should o

NOTE: Equip yourself with antistatic protection and a replacement small form-factor pluggable (SFP) transceiver before replacing an SFP transceiver in

7. Install the new SFP transceiver into the interface port. Ensure that the transceiver is properly seated.8. Reconnect the fiber optic cable.9. View

Installing a Physical Drive Into a Physical-Drive Carrier... 24RAID Controller Module ...

CAUTION: It is recommended that you turn off the host server before turning off the array to prevent loss of data.1. Locate the faulty power supply an

If EMM Status LED is Blinking Amber (5 Times per Sequence) Update the firmware to the latest supported firmware on both the EMMs. For more information

4. Remove the RAID controller module and verify that the pins on backplane and RAID controller module are not bent.5. Reinstall the RAID controller mo

Troubleshooting Array and Expansion Enclosure Connections1. Verify the following:– the SAS OUT status LED is green– for each FC IN port connected to a

6. Close the system.7. Turn on the system and attached peripherals.If the system does not start properly, see Getting Help.8. If the system starts pro

Critical ConditionsThe storage array generates a critical event if the RAID controller module detects a critical condition that could cause immediate

46

5Technical SpecificationsPhysical DisksPhysical disks Up to twelve 3.5 inch or twenty-four 2.5 inch SAS, nearline SAS physical disks, or SAS SSDsRAID

Back-Panel Connectors (Per RAID Controller Module)Serial connector (debug port) One mini-USB portNOTE: For technical support use only.Management Ether

EnvironmentalOperating 10% to 80% (noncondensing) with maximum humidity gradation of 10% per hourStorage 5% to 95% at a maximum wet bulb temperature o

Noncritical Conditions... 45Invalid Sto

50

6Getting HelpLocating Your System Service TagYour system is identified by a unique Express Service Code and Service Tag number. The Express Service Co

6

1About Your SystemIntroductionThe MD3800f and MD3820f Series storage array is designed for high availability, offering redundant access to data storag

Figure 2. Front-Panel Features and Indicators—Dell PowerVault MD3820fFigure 3. Front-Bezel Features and IndicatorsItem Indicator, Button, or Connector

Item Indicator, Button, or Connector DescriptionLights amber as enclosure boots or is reset.Blinks amber when the enclosure is either in a fault state