Dell PowerEdge M805 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítače Dell PowerEdge M805. Dell PowerEdge M805 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 808
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
www.dell.com | support.dell.com
Dell™ PowerConnect™ M6220 Systems
CLI Reference Guide
Zobrazit stránku 0
1 2 3 4 5 6 ... 807 808

Shrnutí obsahu

Strany 1 - CLI Reference Guide

www.dell.com | support.dell.comDell™ PowerConnect™ M6220 SystemsCLI Reference Guide

Strany 2 - Notes, Notices, and Cautions

8 Contentsip igmp snooping leave-time-out. . . . . . . . . . . . . . . . . . . . . . . 185ip igmp snooping mrouter-time-out . . . . . . . . . . . .

Strany 3 - Contents

62 Using the CLIwww.dell.com | support.dell.comRouter OSPFv3 Config From Global Configuration mode, use the ipv6 router ospf command.console(config-rt

Strany 4

Using the CLI 63Starting the CLITo begin running the CLI, perform the following steps: NOTE: This procedure is for use on the console line only. NOT

Strany 5 - 5 User Interface Commands

64 Using the CLIwww.dell.com | support.dell.comThe wizard sets up the following configuration on the switch:• Establishes the initial privileged user

Strany 6 - 7 Address Table Commands

Using the CLI 65• If BOOTP/DHCP is supported and enabled by default, the switch attempts to get its address.• The switch continues to switch traffic.•

Strany 7 - 8 Clock Commands

66 Using the CLIwww.dell.com | support.dell.comFunctional FlowThe functional flow diagram below illustrates the procedures for the Easy Setup Wizard.

Strany 8 - 10 DHCP Filtering Commands

Using the CLI 67Example SessionThis section describes an Easy Setup Wizard session. Refer to the state diagram in the previous section for general flo

Strany 9 - 13 IGMP Snooping Commands

68 Using the CLIwww.dell.com | support.dell.comWould you like to run the set up wizard (you must answer this question within 60 seconds)? [Y/N] y<R

Strany 10 - 15 LACP Commands

Using the CLI 69Now we need to configure your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. Y

Strany 11 - 17 LLDP Commands

70 Using the CLIwww.dell.com | support.dell.comStep 5:If the information is correct, select (Y) to save the configuration and copy to the start-up con

Strany 12 - 21 System Management Commands

Using the CLI 71To use the copy command, the user specifies the source file and the destination file. For example, copy tftp://remotehost/pub/backupfi

Strany 13

Contents 916 Link Dependency Commandslink-dependency group . . . . . . . . . . . . . . . . . . . . . . . . . . . 208no link-dependency group. . . .

Strany 14 - 24 IP Addressing Commands

72 Using the CLIwww.dell.com | support.dell.comCLI through Telnet, SSH, Serial InterfacesThe CLI is accessible through a local serial interface, a rem

Strany 15 - 25 802.1x Commands

Using the CLI 73User Access ControlIn addition to authenticating a user, the CLI also assigns the user access to one of two security levels. Level 1

Strany 16

74 Using the CLIwww.dell.com | support.dell.comSecurity LogsSecurity logs are maintained to record all security events including the following:• User

Strany 17 - 27 QoS Commands

Using the CLI 75Other CLI Tools and CapabilitiesThe CLI has several other capabilities associated with its primary functions.Terminal PagingThe termin

Strany 18 - 28 Radius Commands

76 Using the CLIwww.dell.com | support.dell.comCopyright 1984-2002 Wind River Systems, Inc.CPU: Motorola E500 : Unknown system versionRuntime Name: Vx

Strany 19 - 30 SNMP Commands

Using the CLI 77During the bootup sequence, if a user is connected using the serial interface, the system provides an escape key sequence to interrupt

Strany 20 - 31 Port Channel Commands

78 Using the CLIwww.dell.com | support.dell.com7 - Update boot code8 - Delete backup image9 - Reset the system10 - Restore configuration to factory

Strany 21 - 32 Spanning Tree Commands

Using the CLI 79[Boot Menu] 30Password: *************Boot code utilities menuOptions are:1 - Read/Write memory2 - Display PCI bus3 - Display PCI bu

Strany 22 - 34 Syslog Commands

80 Using the CLIwww.dell.com | support.dell.comSelect option (0-5):CLI command output for the show system id command:console>show system idService

Strany 23 - 37 VLAN Commands

Layer 2 Commands 83Layer 2 CommandsThe chapters that follow describe commands that conform to the OSI model data link layer (Layer 2). Layer 2 command

Strany 24

10 Contentsshow lldp remote-device . . . . . . . . . . . . . . . . . . . . . . . . . . 226show lldp statistics . . . . . . . . . . . . . . . . . .

Strany 25 - 40 ARP Commands

84 Layer 2 Commandswww.dell.com | support.dell.com

Strany 26 - 42 DHCPv6 Commands

Management ACL Commands 85Management ACL Commandsdeny (management)Use the deny command in Management Access-List Configuration mode to set conditions

Strany 27 - 44 IGMP Commands

86 Management ACL Commandswww.dell.com | support.dell.comUser GuidelinesRules with ethernet, vlan, and port-channel parameters are valid only if an IP

Strany 28 - 46 IP Routing Commands

Management ACL Commands 87Syntaxmanagement access-list nameno management access-list name•name—The access list name. (Range: 1 to 32 characters)Defaul

Strany 29 - 47 IPv6 Routing Commands

88 Management ACL Commandswww.dell.com | support.dell.compermit (management)Use the permit command in Management Access-List configuration mode to set

Strany 30 - 49 Multicast Commands

Management ACL Commands 89The following example shows how to configure all the interfaces to be management interfaces except for two interfaces, Ether

Strany 31 - 50 OSPF Commands

90 Management ACL Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePrivileged EXEC mo

Strany 32

User Interface Commands 93User Interface CommandsenableUse the enable command in User EXEC mode to enter the Privileged EXEC mode.SyntaxenableDefault

Strany 33 - 51 OSPFv3 Commands

94 User Interface Commandswww.dell.com | support.dell.comendUse the end command to get the CLI user control back to the privileged execution mode or u

Strany 34

User Interface Commands 95console(config-if-1/g1)# exitconsole(config)# exitconsole#exitconsole>exit (EXEC)Use the exit command in User EXEC mode t

Strany 35 - 53 PIM-SM Commands

Contents 11member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252movemanagement. . . . . . . . . . . . . . . . . . . . . .

Strany 36

96 User Interface Commandswww.dell.com | support.dell.com

Strany 37 - 56 Tunnel Interface Commands

AAA Commands 97AAA Commandsaaa authentication enableUse the aaa authentication enable command in Global Configuration mode to set authentication for a

Strany 38

98 AAA Commandswww.dell.com | support.dell.comUser GuidelinesThe default and optional list names created with the aaa authentication enable command ar

Strany 39 - Command Groups

AAA Commands 99Default ConfigurationIf the default list is not set, only none, or no authentication is checked.Command ModeGlobal Configuration modeUs

Strany 40 - 2 Command Groups

100 AAA Commandswww.dell.com | support.dell.comDefault ConfigurationUses the default set with the command aaa authentication enable.Command ModeLine C

Strany 41

AAA Commands 101ip http authenticationUse the ip http authentication command in Global Configuration mode to specify authentication methods for http s

Strany 42 - Mode Types

102 AAA Commandswww.dell.com | support.dell.comSyntaxip https authentication method1 [method2...]no ip https authentication•method1 [method2...]—Speci

Strany 43

AAA Commands 103Default ConfigurationUses the default set with the command aaa authentication login.Command ModeLine Configuration modeUser Guidelines

Strany 44

104 AAA Commandswww.dell.com | support.dell.compassword (User EXEC)Use the password command in User EXEC mode to allow a user to change the password f

Strany 45

AAA Commands 105ExampleThe following example displays the authentication configuration.console#show authentication methodsLogin Authentication Method

Strany 46

12 Contentstraceroute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28222 ACL Commandsaccess-list . . . . . . . . . . . . . .

Strany 47

106 AAA Commandswww.dell.com | support.dell.comUserName Privilege Password Password Lockout Aging Expir

Strany 48

AAA Commands 107usernameUse the username command in Global Configuration mode to add a new user to the local users database. To remove a user name use

Strany 49

108 AAA Commandswww.dell.com | support.dell.com

Strany 50

Address Table Commands 109Address Table Commandsbridge addressUse the bridge address command in Interface Configuration mode to add a static MAC-layer

Strany 51 - Password Management

110 Address Table Commandswww.dell.com | support.dell.comExampleThe following example adds a permanent static MAC-layer station source address 3aa2.64

Strany 52

Address Table Commands 111no bridge multicast address {mac-multicast-address|ip-multicast-address}•add—Adds ports to the group. If no option is specif

Strany 53

112 Address Table Commandswww.dell.com | support.dell.comno bridge multicast filteringDefault ConfigurationDisabled. All Multicast addresses are flood

Strany 54

Address Table Commands 113Default ConfigurationNo forbidden addresses are defined.Command ModeInterface Configuration (VLAN) modeUser GuidelinesBefore

Strany 55

114 Address Table Commandswww.dell.com | support.dell.combridge multicast forward-allUse the bridge multicast forward-all command in Interface Configu

Strany 56 - 18 Command Groups

Address Table Commands 115 NOTE: Do not use the bridge multicast forbidden forward-unregistered command with the bridge multicast forward-unregistere

Strany 57

Contents 13ip address vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305ip default-gateway . . . . . . . . . . . . . . . . . .

Strany 58 - 20 Command Groups

116 Address Table Commandswww.dell.com | support.dell.com•discard—Discards frames with unlearned source addresses. This is the default if no option is

Strany 59

Address Table Commands 117Command ModeInterface Configuration (Ethernet, Port-channel) modeUser GuidelinesThis command has no user guidelines.ExampleT

Strany 60

118 Address Table Commandswww.dell.com | support.dell.com1 0000.8420.5010 1/g1 Dynamic1 0000.E26D.2C2A 1/g1 Dynamic1

Strany 61

Address Table Commands 119show bridge address-table staticUse the show bridge address-table static command in Privileged EXEC mode to display static e

Strany 62

120 Address Table Commandswww.dell.com | support.dell.com•format—Multicast address format. Can be ip or mac.Default Configuration If format is unspec

Strany 63

Address Table Commands 121•vlan_id—A valid VLAN ID value.Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC mo

Strany 64

122 Address Table Commandswww.dell.com | support.dell.comExampleIn this example, all classes of entries in the port-lock status are displayed.console#

Strany 65

Address Table Commands 123Command ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExamplesThe following example displays dy

Strany 66

124 Address Table Commandswww.dell.com | support.dell.com

Strany 67

Clock Commands 125Clock Commandsshow clockUse the show clock command in User EXEC mode to display the time and date from the system clock.Syntaxshow

Strany 68

14 Contentsdot1x auth-not-req . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329dot1x guest-vlan. . . . . . . . . . . . . . . . . . . .

Strany 69

126 Clock Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser G

Strany 70

Clock Commands 127Unicast servers:server status Last response--------- ----------- -------------------------- sntp authenti

Strany 71

128 Clock Commandswww.dell.com | support.dell.com•key-number— number (Range: 1 - 4294967295)•value— value (Range: 1-8 characters)Default valueNo authe

Strany 72

Clock Commands 129sntp client poll timerUse the sntp client poll timer command in Global Configuration mode to set the polling time for the Simple Net

Strany 73

130 Clock Commandswww.dell.com | support.dell.com•key-number — Authentication key to use when sending packets to this peer. (Range: 1-4294967295)•prio

Strany 74

Clock Commands 131User GuidelinesThis command is relevant for both received Unicast and Broadcast.ExampleThe following defines SNTP trusted-key.consol

Strany 75

132 Clock Commandswww.dell.com | support.dell.comSyntaxclock timezone hours-offset [minutes minutes-offset] [zone acronym]•hours-offset—Hours differen

Strany 76

Clock Commands 133clock summer-time recurringUse the clock summer-time recurring {usa | eu | {week day month hh:mm week day month hh:mm}} [offset offs

Strany 77

134 Clock Commandswww.dell.com | support.dell.com•date—Day of the month. (Range: 1–31)•month—Month. (Range: The first three letters by name; jan, for

Strany 78 - 40 Command Groups

Clock Commands 135Exampleconsole(config)#no clock summer-time recurringshow clockUse the show clock command to display the time and date from the syst

Strany 79

Contents 1527 QoS Commandsassign-queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355class . . . . . . . . . . . . . . . . . .

Strany 80

136 Clock Commandswww.dell.com | support.dell.comBegins at first Sunday of April at 2:00.Ends at last Sunday of October at 2:00.Offset is 60 minutes.

Strany 81

Denial of Service Commands 139Denial of Service Commandsdos-control firstfragUse the dos-control firstfrag command in Global Configuration mode to ena

Strany 82

140 Denial of Service Commandswww.dell.com | support.dell.comdos-control icmpUse the dos-control icmp command in Global Configuration mode to enable M

Strany 83

Denial of Service Commands 141Command ModeGlobal Configuration modeUser GuidelinesThis command has no user guidelines. ExampleThe following example ac

Strany 84 - 46 Command Groups

142 Denial of Service Commandswww.dell.com | support.dell.comControl Flags set to 0 and TCP Sequence Number set to 0, having TCP Flags FIN, URG, and P

Strany 85

Denial of Service Commands 143ExampleThe following example activates TCP Fragment Denial of Service protection.console(config)#dos-control tcpfragshow

Strany 86

144 Denial of Service Commandswww.dell.com | support.dell.com

Strany 87

DHCP Filtering Commands 145DHCP Filtering Commandsip dhcp filteringUse the ip dhcp filtering command in Global Configuration mode to enable DHCP filte

Strany 88 - Command Completion

146 DHCP Filtering Commandswww.dell.com | support.dell.comno ip dhcp filtering trustDefault ConfigurationAny DHCP response received on a trusted port

Strany 89 - Keyboard Shortcuts

DHCP Filtering Commands 1471/g6 yes

Strany 90 - Command Scripting

16 Contentsmatch srcip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372match srcl4port. . . . . . . . . . . . . . . . . . . . .

Strany 91 - CLI Command Modes

148 DHCP Filtering Commandswww.dell.com | support.dell.com

Strany 92 - User EXEC Mode

Ethernet Configuration Commands 149Ethernet Configuration Commandsclear countersUse the clear counters command in Privileged EXEC mode to clear statis

Strany 93 - Global Configuration Mode

150 Ethernet Configuration Commandswww.dell.com | support.dell.com•string—Comment or a description of the port attached to this interface. (Range: 1 t

Strany 94

Ethernet Configuration Commands 151ExampleThe following example configures the duplex operation of Ethernet port 5 to force full duplex operation.cons

Strany 95 - Using the CLI 57

152 Ethernet Configuration Commandswww.dell.com | support.dell.comCommand ModeGlobal Configuration modeUser GuidelinesThis command has no user guideli

Strany 96 - Navigating CLI Command Modes

Ethernet Configuration Commands 153mdixUse the mdix command in Interface Configuration mode to enable cable crossover on a given interface. To disable

Strany 97

154 Ethernet Configuration Commandswww.dell.com | support.dell.comCommand ModeInterface Configuration (Ethernet) modeUser GuidelinesThe value set allo

Strany 98

Ethernet Configuration Commands 155show interfaces advertiseUse the show interfaces advertise command in Privileged EXEC mode to display information a

Strany 99

156 Ethernet Configuration Commandswww.dell.com | support.dell.comshow interfaces configurationUse the show interfaces configuration command in User

Strany 100

Ethernet Configuration Commands 157show interfaces countersUse the show interfaces counters command in User EXEC mode to display traffic seen by the

Strany 101 - Starting the CLI

Contents 17radius-server deadtime . . . . . . . . . . . . . . . . . . . . . . . . . . . 396radius-server host. . . . . . . . . . . . . . . . . . . .

Strany 102 - Using the CLI

158 Ethernet Configuration Commandswww.dell.com | support.dell.com3/g1 123899 1788Port OutOctets OutUcastPkts---- ---------- ---------1/g1

Strany 103 - Using the CLI 65

Ethernet Configuration Commands 159Deferred Transmissions: 0Late Collisions: 0Excessive Collisions: 0Oversize Packets: 0Internal MAC Rx Errors: 0Recei

Strany 104 - 66 Using the CLI

160 Ethernet Configuration Commandswww.dell.com | support.dell.comshow interfaces descriptionUse the show interfaces description command in User EXEC

Strany 105 - Example Session

Ethernet Configuration Commands 161Ch Description---- -----------1 Outputshow interfaces statusUse the show interfaces status command in User

Strany 106

162 Ethernet Configuration Commandswww.dell.com | support.dell.com State---- ---- ------ ----- ---- -----1 10

Strany 107 - Using the CLI 69

Ethernet Configuration Commands 163Command ModePrivileged EXEC mode.User GuidelinesThis command has no user guidelines.ExamplesThe following examples

Strany 108 - Using CLI Functions and Tools

164 Ethernet Configuration Commandswww.dell.com | support.dell.com--More-- or (q)uitBroadcast Packets Received... 76702 Tot

Strany 109 - Management Interface Security

Ethernet Configuration Commands 165Broadcast Packets Transmitted... 4 Total Transmit Errors... 0FCS Erro

Strany 110 - User Accounts Management

166 Ethernet Configuration Commandswww.dell.com | support.dell.comPackets Transmitted Without Errors... 91652Unicast Packets Transmitted...

Strany 111 - User Access Control

Ethernet Configuration Commands 167ExamplesThe following example shows storm control configurations for all valid Ethernet ports. The second example s

Strany 112 - Management ACAL

Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates

Strany 113 - Boot Message

18 Contentsshow snmp engineID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423show snmp filters. . . . . . . . . . . . . . . . . . . . .

Strany 114 - Boot Utility Menu

168 Ethernet Configuration Commandswww.dell.com | support.dell.comThe following example re-enables ethernet port 1/g5.console(config)#interface ethern

Strany 115 - Using the CLI 77

Ethernet Configuration Commands 169storm-control broadcastUse the storm-control broadcast command in Interface Configuration mode to enable broadcast

Strany 116 - FRU Utility Menu

170 Ethernet Configuration Commandswww.dell.com | support.dell.comCommand ModeInterface Configuration (Ethernet) modeUser Guidelines This command has

Strany 117 - Using the CLI 79

GVRP Commands 173GVRP Commandsclear gvrp statisticsUse the clear gvrp statistics command in Privileged EXEC mode to clear all the GVRP statistics info

Strany 118 - Monitoring Traps from CLI

174 GVRP Commandswww.dell.com | support.dell.comno garp timer•join—Indicates the time in centiseconds that PDUs are transmitted. •leave—Indicates the

Strany 119 - Layer 2 Commands

GVRP Commands 175Syntaxgvrp enableno gvrp enableDefault ConfigurationGVRP is globally disabled.Command ModeGlobal Configuration modeUser GuidelinesThi

Strany 120 - 84 Layer 2 Commands

176 GVRP Commandswww.dell.com | support.dell.comExampleThe following example enables GVRP on ethernet 1/g8.console(config)#interface ethernet 1/g8cons

Strany 121 - Management ACL Commands

GVRP Commands 177Default ConfigurationBy default, dynamic VLAN creation is enabled.Command ModeInterface Configuration (Ethernet, Port-Channel) modeUs

Strany 122

178 GVRP Commandswww.dell.com | support.dell.comconsole# show gvrp configuration Join Leave LeaveAll Port Interface

Strany 123 - Examples

GVRP Commands 179•port-channel-number—A valid port-channel index.Default ConfigurationThis command has no default configuration.Command ModeUser EXEC

Strany 124

Contents 1932 Spanning Tree Commandsabort (mst) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451clear spanning-tree detected-p

Strany 125 - Management ACL Commands 89

180 GVRP Commandswww.dell.com | support.dell.comSyntaxshow gvrp statistics [ethernet interface | port-channel port-channel-number]•interface—A valid E

Strany 126

GVRP Commands 1811/g5 0 0 0 0 0 0 0 0 0 0 0 01/g6 0 0 0 0 0 0 0 0 0 0

Strany 127 - User Interface Commands

182 GVRP Commandswww.dell.com | support.dell.com

Strany 128

IGMP Snooping Commands 183IGMP Snooping Commandsip igmp snooping (global)Use the ip igmp snooping command in Global Configuration mode to globally ena

Strany 129

184 IGMP Snooping Commandswww.dell.com | support.dell.comno ip igmp snoopingDefault ConfigurationIGMP snooping is disabled.Command ModeInterface Confi

Strany 130 - 96 User Interface Commands

IGMP Snooping Commands 185ip igmp snooping leave-time-outUse the ip igmp snooping leave-time-out command in Interface Configuration mode to configure

Strany 131 - AAA Commands

186 IGMP Snooping Commandswww.dell.com | support.dell.com•time-out—mrouter timeout in seconds for IGMP. (Range: 1 - 2147483647)Default ConfigurationTh

Strany 132

IGMP Snooping Commands 1871 224-239.130|2.2.3 1/g1, 2/g219 224-239.130|2.2.8 1/g9-g11IGMP Reporters that are forbidden static

Strany 133

188 IGMP Snooping Commandswww.dell.com | support.dell.comMax Response Time... 10Multicast Router Present Expiration Time...

Strany 134

IGMP Snooping Commands 189ip igmp snooping (VLAN)Use the ip igmp snooping command in VLAN Configuration mode to enable IGMP snooping on a particular i

Strany 135

20 Contents33 SSH Commandscrypto key generate dsa. . . . . . . . . . . . . . . . . . . . . . . . . . . 480crypto key generate rsa. . . . . . . . . .

Strany 136

190 IGMP Snooping Commandswww.dell.com | support.dell.comDefault ConfigurationIGMP snooping fast-leave mode is disabled on VLANs by default.Command Mo

Strany 137 - (Line Configuration)

IGMP Snooping Commands 191console(config-vlan)#ip igmp snooping groupmembership-interval 2 520ip igmp snooping maxresponseThis command sets the IGMP M

Strany 138 - (User EXEC)

192 IGMP Snooping Commandswww.dell.com | support.dell.comSyntaxip igmp snooping mcrtexpiretime vlan-id secondsno ip igmp mcrtexpiretime vlan-id•vlan i

Strany 139 - AAA Commands 105

IGMP Snooping Querier Commands 195IGMP Snooping Querier Commandsip igmp snooping querierThis command enables/disables IGMP Snooping Querier on the sys

Strany 140

196 IGMP Snooping Querier Commandswww.dell.com | support.dell.comExampleThe following example enables IGMP snooping querier in VLAN Configuration mode

Strany 141

IGMP Snooping Querier Commands 197ip igmp snooping querier query-intervalThis command sets the IGMP Querier Query Interval time, which is the amount o

Strany 142 - 108 AAA Commands

198 IGMP Snooping Querier Commandswww.dell.com | support.dell.comCommand ModeGlobal Configuration modeUser GuidelinesThis command has no user guidelin

Strany 143 - Address Table Commands

IGMP Snooping Querier Commands 199continues sending periodic queries. The no form of this command sets the snooping querier not to participate in the

Strany 144

200 IGMP Snooping Querier Commandswww.dell.com | support.dell.com• VLAN Operational State—Indicates whether IGMP Snooping Querier is in the Querier or

Strany 145

LACP Commands 201LACP Commandslacp port-priorityUse the lacp port-priority command in Interface Configuration mode to configure the priority value for

Strany 146

Contents 21show logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498show logging file . . . . . . . . . . . . . . . . . . .

Strany 147 - Address Table Commands 113

202 LACP Commandswww.dell.com | support.dell.comSyntaxlacp system-priority valueno lacp system-priority•value—Value of the priority. (Range: 1 - 65535

Strany 148

LACP Commands 203ExampleThe following example assigns an administrative LACP timeout for port 1/g8 to a long timeout value.console(config)#interface e

Strany 149 - Address Table Commands 115

204 LACP Commandswww.dell.com | support.dell.com LACP Activity: ACTIVE Aggregation: AGGREGATAB

Strany 150

LACP Commands 205Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser GuidelinesThis command has no use

Strany 151 - Address Table Commands 117

206 LACP Commandswww.dell.com | support.dell.com

Strany 152

Link Dependency Commands 207Link Dependency Commandslink-dependency groupUse the link-dependency group command to enter the link-dependency mode to co

Strany 153 - Address Table Commands 119

208 Link Dependency Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModeGlobal Configura

Strany 154

Link Dependency Commands 209•intf-list—List of Ethernet interfaces. Separate nonconsecutive ports with a comma and no spaces. Use a hyphen to designat

Strany 155 - Address Table Commands 121

210 Link Dependency Commandswww.dell.com | support.dell.comno add port-channelUse the no add port-channel command to remove member port-channels from

Strany 156

Link Dependency Commands 211Exampleconsole(config-linkDep-group-1)#depends-on ethernet g10no depends-on ethernetUse the no depends-on ethernet command

Strany 157

22 Contentsprotocol vlan group all. . . . . . . . . . . . . . . . . . . . . . . . . . . . 517show dvlan-tunnel. . . . . . . . . . . . . . . . . . .

Strany 158 - 124 Address Table Commands

212 Link Dependency Commandswww.dell.com | support.dell.comUser GuidelinesNo specific guidelinesExampleconsole(config-linkDep-group-1)#depends-on port

Strany 159 - Clock Commands

Link Dependency Commands 213Command ModePrivileged EXEC modeUser GuidelinesNo specific guidelinesExampleThe following command shows link dependencies

Strany 160

214 Link Dependency Commandswww.dell.com | support.dell.com

Strany 161 - Clock Commands 127

LLDP Commands 215LLDP Commandsclear lldp remote-dataUse the clear lldp remote-data command in Privileged EXEC mode to delete all LLDP information from

Strany 162

216 LLDP Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe followin

Strany 163 - Clock Commands 129

LLDP Commands 217no lldp notification-interval• interval—The smallest interval in seconds at which to send remote data change notifications. (Range: 5

Strany 164

218 LLDP Commandswww.dell.com | support.dell.comlldp timersUse the lldp timers command in Global Configuration mode to set the timing parameters for l

Strany 165 - Clock Commands 131

LLDP Commands 219Syntaxlldp transmitno lldp transmitDefault ConfigurationLLDP is disabled on all supported interfaces.Command Mode Interface Configura

Strany 166

220 LLDP Commandswww.dell.com | support.dell.comlldp transmit-tlvUse the lldp transmit-tlv command in Interface Configuration mode to specify which op

Strany 167 - Clock Commands 133

LLDP Commands 221Command ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe following example displays the current

Strany 168

Contents 2338 Web Server Commandscommon-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542country . . . . . . . . . . . . . . .

Strany 169 - Clock Commands 135

222 LLDP Commandswww.dell.com | support.dell.comExample 1:console#show lldp connectionsLocal RemoteInterface Device ID Port ID

Strany 170 - Offset is 60 minutes

LLDP Commands 223ExamplesThis example show how the information is displayed when you use the command with the all parameter.console#show lldp interfac

Strany 171 - Denial of Service Commands

224 LLDP Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExamplesThese examples show advertised LLDP local d

Strany 172

LLDP Commands 225show lldp remote-deviceUse the lldp remote-device command in Privileged EXEC mode to display the current LLDP remote data. This comma

Strany 173

226 LLDP Commandswww.dell.com | support.dell.comPort ID: 01:23:45:67:89:ACPort Description: 1/g4Management Address: 192.168.112.1TTL: 60 secondsshow l

Strany 174

LLDP Commands 227ExamplesThe following examples shows an example of the display of current LLDP traffic statistics.console#show lldp statistics allLas

Strany 175

228 LLDP Commandswww.dell.com | support.dell.comThe following table explains the fields in this example.Parameter DescriptionLast Update The value of

Strany 176

Password Management Commands 231Password Management Commandspasswords agingUse the passwords aging command in Global Configuration mode to implement e

Strany 177 - DHCP Filtering Commands

232 Password Management Commandswww.dell.com | support.dell.comUse the no form of this command to disable the password history function.Syntaxpassword

Strany 178

Password Management Commands 233Command ModeGlobal Configuration mode.User GuidelinesThis command has no user guidelines.ExampleThe following example

Strany 179 - 1/g6 yes

24 Contentsarp resptime. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562arp retries. . . . . . . . . . . . . . . . . . . . . . .

Strany 180 - 148 DHCP Filtering Commands

234 Password Management Commandswww.dell.com | support.dell.comSyntaxshow passwords configurationDefault ConfigurationThis command has no default conf

Strany 181

Port Monitor Commands 237Port Monitor Commandsmonitor sessionUse the monitor session command in Global Configuration mode to configure a probe port an

Strany 182

238 Port Monitor Commandswww.dell.com | support.dell.comExampleThe following examples shows various port monitoring configurations.console(config)#mon

Strany 183

Port Monitor Commands 239show monitor sessionUse the show monitor session command in Privileged EXEC mode to display status of port monitoring.Syntaxs

Strany 184

240 Port Monitor Commandswww.dell.com | support.dell.com

Strany 185

PHY Diagnostics Commands 241PHY Diagnostics Commandsshow copper-ports cable-lengthUse the show copper-ports cable-length command in Privileged EXEC mo

Strany 186

242 PHY Diagnostics Commandswww.dell.com | support.dell.comshow copper-ports tdrUse the show copper-ports tdr command in Privileged EXEC mode to displ

Strany 187

PHY Diagnostics Commands 243Syntax Description•interface—A valid Ethernet port. The full syntax is unit / port.Default ConfigurationThis command has n

Strany 188 - Command Modes

244 PHY Diagnostics Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePrivileged EXEC

Strany 189 - Example

System Management Commands 247System Management Commandsasset-tagUse the asset-tag command in Global Configuration mode to specify the switch asset ta

Strany 190

Contents 25show ipv6 dhcp binding . . . . . . . . . . . . . . . . . . . . . . . . . . . 581show ipv6 dhcp interface . . . . . . . . . . . . . . . .

Strany 191

248 System Management Commandswww.dell.com | support.dell.comSyntaxcut-through modeDefault ConfigurationThis command has no default configuration.Comm

Strany 192

System Management Commands 249ip addressUse the ip address command to set a static OOB port IP address.Syntaxip address addr mask gw•addr—IP address t

Strany 193

250 System Management Commandswww.dell.com | support.dell.comconsole(config-if)#ip address noneip addressUse the ip address command to enable DHCP/BOO

Strany 194

System Management Commands 251Command ModeStack Global ConfigurationUser GuidelinesThe switch index can be obtained by executing the show supported sw

Strany 195

252 System Management Commandswww.dell.com | support.dell.comExampleThe following example displays how to move the Management Switch functionality fro

Strany 196

System Management Commands 253User GuidelinesNo specific guidelines.Exampleconsole(config)#stackconsole(config-stack)#no standbyFastpath will automati

Strany 197

254 System Management Commandswww.dell.com | support.dell.com•Destination unreachable—The gateway for this destination indicates that the destination

Strany 198

System Management Commands 255Syntaxreload [unit]•unit —Unit number to be reloaded.Default ConfigurationThis command has no default configuration.Comm

Strany 199

256 System Management Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following example displaysc

Strany 200

System Management Commands 257Default ConfigurationThis command has no default configuration.User GuidelinesNo specific guidelines.ExampleConsole#show

Strany 201

26 Contentsshow ip igmp groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602show ip igmp interface . . . . . . . . . . . . . . . . .

Strany 202

258 System Management Commandswww.dell.com | support.dell.comshow memory cpuUse the show memory cpu command to check the total and available RAM space

Strany 203 - GVRP Commands

System Management Commands 259Exampleconsole#show process cpuMemory Utilization Reportstatus bytes------ ----------Free 27896864Alloc 168268448Task

Strany 204

260 System Management Commandswww.dell.com | support.dell.comshow sessionsUse the show sessions command in Privileged EXEC mode to display a list of t

Strany 205 - GVRP Commands 175

System Management Commands 261show stack-portUse the show stack-port command in Privileged EXEC mode to display summary stack-port information for all

Strany 206

262 System Management Commandswww.dell.com | support.dell.comshow stack-port countersUse the show stack-port counters command in Privileged EXEC mode

Strany 207 - GVRP Commands 177

System Management Commands 263The following table describes the fields in the example.Field DescriptionUnit UnitInterface PortTx Data Rate Transmit da

Strany 208

264 System Management Commandswww.dell.com | support.dell.comshow stack-port diag NOTE: This command is intended only for Field Application Engineers

Strany 209

System Management Commands 265RFCS : Received Frame Check Sequence ErrorsRFRG : Received Fragment ErrorsRJBR : Received Jabber ErrorsRUND : Received U

Strany 210

266 System Management Commandswww.dell.com | support.dell.comSyntaxshow stack-standbyDefault ConfigurationThis command has no default configuration.Co

Strany 211 - GVRP Commands 181

System Management Commands 267ExampleThe following example displays the information for supported switch types.console>show supported switchtype

Strany 212 - 182 GVRP Commands

Contents 27show ip protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 622show ip route . . . . . . . . . . . . . . . . . . . . .

Strany 213 - IGMP Snooping Commands

268 System Management Commandswww.dell.com | support.dell.comThe following table describes the fields in the example.Field DescriptionSwitch Type This

Strany 214

System Management Commands 269show switchUse the show switch command in User EXEC mode to display information about all units in the stack. Use the sh

Strany 215 - IGMP Snooping Commands 185

270 System Management Commandswww.dell.com | support.dell.comThe following table describes the fields in the example.This example displays information

Strany 216

System Management Commands 271Different fields in the display are explained as follows:show systemUse the show system command in User EXEC mode comman

Strany 217

272 System Management Commandswww.dell.com | support.dell.comExampleThe following example displays system information.console>show systemSystem Des

Strany 218

System Management Commands 273show system idUse the show system id command in User EXEC mode to display the system identity information.Syntaxshow sys

Strany 219 - IGMP Snooping Commands 189

274 System Management Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.Exampl

Strany 220

System Management Commands 275ExampleThe following example displays a system version (this version number is only for demonstration purposes).console&

Strany 221

276 System Management Commandswww.dell.com | support.dell.comstandbyUse the standby command to configure the standby in the stack. This unit comes up

Strany 222

System Management Commands 277User GuidelinesSwitches that do not have the hardware capability to become the Management Switch are not eligible for ma

Strany 223

Contents 1Contents1 Command GroupsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Command Groups. . . . . . . . .

Strany 224

28 Contentsshow ipv6 brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645show ipv6 interface. . . . . . . . . . . . . . . . . .

Strany 225

278 System Management Commandswww.dell.com | support.dell.com•port — A decimal TCP port number, or one of the keywords from the port table in the usag

Strany 226

System Management Commands 279Port TableKeyword Description Port Numberbgp Border Gateway Protocol 179chargen Character generator 19cmd Remote comman

Strany 227

280 System Management Commandswww.dell.com | support.dell.comExampleFollowing is an example of using the telnet command to connect to 176.213.10.50.co

Strany 228

System Management Commands 281•time_out — The number of seconds to wait for a response to a probe packet. (Range: 1- 60)• ip-address— One of the inter

Strany 229 - LACP Commands

282 System Management Commandswww.dell.com | support.dell.comThe following example uses the iterative process to obtain command parameters, and displa

Strany 230

ACL Commands 285ACL Commandsaccess-listUse the access-list command in Global Configuration mode to create an Access Control List (ACL) that is identif

Strany 231 - LACP Commands 203

286 ACL Commandswww.dell.com | support.dell.com•log—Specifies that this rule is to be logged.•assign-queue queue-id—Specifies the particular hardware

Strany 232

ACL Commands 287•dstmac—Valid destination MAC address in format xxxx.xxxx.xxxx.•destmacmask—Valid MAC address bitmask for the destination MAC address

Strany 233

288 ACL Commandswww.dell.com | support.dell.comExampleThe following example configures a MAC ACL to deny traffic from MAC address 0806.c200.0000.conso

Strany 234 - 206 LACP Commands

ACL Commands 289mac access-groupUse the mac access-group command in Global Configuration or Interface Configuration mode to attach a specific MAC Acce

Strany 235 - Link Dependency Commands

Contents 29show ip mcast mroute group . . . . . . . . . . . . . . . . . . . . . . . . 669show ip mcast mroute source. . . . . . . . . . . . . . . .

Strany 236

290 ACL Commandswww.dell.com | support.dell.comSyntaxmac access-list extended nameno mac access-list extended name •name —Name of the access list. (Ra

Strany 237 - Link Dependency Commands 209

ACL Commands 291ExampleThe following example shows the mac access-list extended rename command.console(config)#mac access-list extended rename DELL1 D

Strany 238

292 ACL Commandswww.dell.com | support.dell.comSyntaxshow mac access-list name•name—Identifies a specific MAC access list to display.Default Configura

Strany 239 - Link Dependency Commands 211

Line Commands 295Line Commandsexec-timeoutUse the exec-timeout command in Line Configuration mode to set the interval that the system waits for user i

Strany 240

296 Line Commandswww.dell.com | support.dell.comhistoryUse the history command in Line Configuration mode to enable the command history function. To d

Strany 241

Line Commands 297User GuidelinesThis command has no user guidelines.ExampleThe following example configures the command history buffer size to 20 comm

Strany 242 - 214 Link Dependency Commands

298 Line Commandswww.dell.com | support.dell.com•console—Console terminal line.•telnet—Virtual terminal for remote console access (Telnet).•ssh—Virtua

Strany 243 - LLDP Commands

Line Commands 299Syntaxspeed {bps}no speed•bps—Baud rate in bits per second (bps). The options are 2400, 9600, 19200, 38400, 57600, and 115200.Default

Strany 244

300 Line Commandswww.dell.com | support.dell.com

Strany 245 - LLDP Commands 217

IP Addressing Commands 301IP Addressing Commandsclear hostUse the clear host command in Privileged EXEC mode to delete entries from the host name-to-a

Strany 246

30 Contentsdistribute-list out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690enable. . . . . . . . . . . . . . . . . . . . . . . .

Strany 247 - LLDP Commands 219

302 IP Addressing Commandswww.dell.com | support.dell.comSyntaxhelper-address ip-address [udp-port-list ]no helper-address ip-address•ip-address—Desti

Strany 248

IP Addressing Commands 303console(config-vlan1)#helper-address 131.108.1.27 30,100-120,201interface out-of-bandUse the interface out-of-band command t

Strany 249 - LLDP Commands 221

304 IP Addressing Commandswww.dell.com | support.dell.comUser GuidelinesIP address protocol should be set to none before setting the static IP address

Strany 250

IP Addressing Commands 305Syntaxip address vlan vlanid no ip address vlan •vlanid—vlan identification. (Range 1-4093)Default ConfigurationThe default

Strany 251

306 IP Addressing Commandswww.dell.com | support.dell.comip domain-lookupUse the ip domain-lookup command in Global Configuration mode to enable IP Do

Strany 252

IP Addressing Commands 307Command ModeGlobal Configuration modeUser GuidelinesThis command has no user guidelines.ExampleThe following example defines

Strany 253

308 IP Addressing Commandswww.dell.com | support.dell.comThe setting of helper address for specific interface has precedence over a setting of helper

Strany 254

IP Addressing Commands 309ExampleThe following example defines a static host name-to-address mapping in the host cache.console(config)#ip host account

Strany 255

310 IP Addressing Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesNote that this command only show ARP entries u

Strany 256 - Parameter Description

IP Addressing Commands 311Configured host name-to-address mapping:Host Addresses-------------------------- ---------------

Strany 257 - Password Management Commands

Contents 31show ip ospf range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712show ip ospf statistics. . . . . . . . . . . . . . . . .

Strany 258

312 IP Addressing Commandswww.dell.com | support.dell.comshow ip interface managementUse the show ip interface management command in User EXEC mode to

Strany 259

802.1x Commands 315802.1x Commandsaaa authentication dot1x Use the aaa authentication dot1x command in Global Configuration mode to create an authenti

Strany 260

316 802.1x Commandswww.dell.com | support.dell.comdot1x max-reqUse the dot1x max-req command in Interface Configuration mode to set the maximum number

Strany 261 - Port Monitor Commands

802.1x Commands 317•auto — Enables 802.1x authentication on the interface and causes the port to transition to the authorized or unauthorized state ba

Strany 262 - 238 Port Monitor Commands

318 802.1x Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following command manually initiates a

Strany 263

802.1x Commands 319Default ConfigurationThe default for this command is disabled.Command ModeGlobal Configuration modeUser GuidelinesThis command has

Strany 264 - 240 Port Monitor Commands

320 802.1x Commandswww.dell.com | support.dell.comExampleThe following example sets the number of seconds that the switch remains in the quiet state f

Strany 265 - PHY Diagnostics Commands

802.1x Commands 321Syntaxdot1x timeout server-timeout seconds no dot1x timeout server-timeout•seconds — Time in seconds that the switch waits for a re

Strany 266

322 802.1x Commandswww.dell.com | support.dell.comUser Guidelines Change the default value of this command only to adjust for unusual circumstances, s

Strany 267

802.1x Commands 323show dot1xUse the show dot1x command in Privileged EXEC mode to display 802.1x status for the switch or for the specified interface

Strany 268

32 Contentsdistance ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733enable. . . . . . . . . . . . . . . . . . . . . . . . .

Strany 269 - System Management Commands

324 802.1x Commandswww.dell.com | support.dell.comThe following table describes the significant fields shown in the display:show dot1x statisticsUse t

Strany 270

802.1x Commands 325Syntaxshow dot1x statistics ethernetinterface•interface — Ethernet port name. The full syntax is unit/port.Default ConfigurationThi

Strany 271

326 802.1x Commandswww.dell.com | support.dell.comThe following table describes the significant fields shown in the display.show dot1x usersUse the sh

Strany 272

802.1x Commands 327Command Mode Privileged EXEC modeUser Guidelines This command has no user guidelines.ExampleThe following example displays 802.1x u

Strany 273

328 802.1x Commandswww.dell.com | support.dell.com802.1 Advanced Featuresdot1x auth-not-reqUse the dot1x auth-not-req command in Interface Configurati

Strany 274

802.1x Commands 329Command ModeInterface Configuration (VLAN) modeUser GuidelinesUse the dot1x guest-vlan enable command in Interface Configuration mo

Strany 275

330 802.1x Commandswww.dell.com | support.dell.comdot1x multiple-hostsUse the dot1x multiple-hosts command in Interface Configuration mode to allow mu

Strany 276

802.1x Commands 331•discard-shutdown — Discard frames with source addresses that are not the supplicant address, and shut down the port.•trap seconds—

Strany 277

332 802.1x Commandswww.dell.com | support.dell.comExampleThe following example displays 802.1x advanced features for the switch.console#show dot1x adv

Strany 278

Configuration and Image File Commands 335Configuration and Image File Commandsboot systemUse the boot system command in Privileged EXEC mode to specif

Strany 279

Contents 33show ipv6 ospf neighbor. . . . . . . . . . . . . . . . . . . . . . . . . . . 757show ipv6 ospf range . . . . . . . . . . . . . . . . . .

Strany 280

336 Configuration and Image File Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePri

Strany 281

Configuration and Image File Commands 337Default ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Guideline

Strany 282

338 Configuration and Image File Commandswww.dell.com | support.dell.comStoring the Running or Startup Configuration on a ServerUse the copy running-c

Strany 283

Configuration and Image File Commands 339Destination Filename... image1Management access will be blocked for the duration of t

Strany 284

340 Configuration and Image File Commandswww.dell.com | support.dell.comUser GuidelinesNote that the active image cannot be deleted.ExampleThe followi

Strany 285

Configuration and Image File Commands 341Default ConfigurationNo description is attached to the file.Command ModePrivileged EXEC modeUser GuidelinesTh

Strany 286

342 Configuration and Image File Commandswww.dell.com | support.dell.comExampleconsole#ftpdownload 10.240.3.108/dell/image1 image user randall passwor

Strany 287 - Field Description

Configuration and Image File Commands 343Command ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe following examp

Strany 288

344 Configuration and Image File Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidel

Strany 289

Configuration and Image File Commands 345script validateUse the script validate command in Privileged EXEC mode to validate a script file by parsing e

Strany 290

34 Contentsip pim-trapflags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 776show ip pimsm . . . . . . . . . . . . . . . . . . . . .

Strany 291

346 Configuration and Image File Commandswww.dell.com | support.dell.comconsole#show backup-configsoftware version 1.1hostname deviceinterface etherne

Strany 292

Configuration and Image File Commands 347Image Descriptions image1 : default image image2 : Images currently available on Flash-----------------------

Strany 293

348 Configuration and Image File Commandswww.dell.com | support.dell.com--------- ---------------image1 6351288 image2

Strany 294

Configuration and Image File Commands 349duplex fullspeed 1000exitinterface ethernet 1/g2ip address 176.243.100.100 255.255.255.0duplex fullspeed 1000

Strany 295

350 Configuration and Image File Commandswww.dell.com | support.dell.comexitinterface ethernet 1/g2ip address 176.243.100.100 255.255.255.0duplex full

Strany 296

QoS Commands 353QoS Commandsassign-queueUse the assign-queue command in Policy-Class-Map Configuration mode to modify the queue ID to which the associ

Strany 297

354 QoS Commandswww.dell.com | support.dell.comno class•classname—Specifies the name of an existing DiffServ class. (Range: 1 - 31 characters)Default

Strany 298

QoS Commands 355The CLI mode is changed to Class-Map Configuration when this command is executed successfully.ExampleThe following example creates a c

Strany 299

356 QoS Commandswww.dell.com | support.dell.comSyntaxclassofservice dot1p-mapping 802.1ppriority trafficclassno classofservice dot1p-mapping •802.1ppr

Strany 300 - Keywords Table

QoS Commands 357ExampleThe following example displays mapping for IP DSCP 1 and traffic class 2.console(config)#classofservice ip-dscp-mapping 1 2clas

Strany 301 - Port Table

Contents 35ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794ip rip authentication. . . . . . . . . . . . . . . . .

Strany 302

358 QoS Commandswww.dell.com | support.dell.comconform-colorUse the conform-color command in Policy-Class-Map Configuration mode to specify second-lev

Strany 303

QoS Commands 359Command ModeGlobal Configuration mode or Interface Configuration (Ethernet, Port-channel) modeUser GuidelinesThe maximum number of que

Strany 304

360 QoS Commandswww.dell.com | support.dell.comconsole(config)#cos-queue strict 1 2 4diffservUse the diffserv command in Global Configuration mode to

Strany 305 - ACL Commands

QoS Commands 361User GuidelinesThis command has no user guidelines.ExampleThe following example displays how to specify that matching packets are to b

Strany 306

362 QoS Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePolicy-Class-Map Configurati

Strany 307

QoS Commands 363match class-mapUse the match class-map command to add to the specified class definition the set of match conditions defined for anothe

Strany 308

364 QoS Commandswww.dell.com | support.dell.comThe following example deletes the match conditions defined for the Dell class from the class currently

Strany 309

QoS Commands 365Default ConfigurationThis command has no default configuration.Command ModeClass-Map Configuration modeUser GuidelinesThis command has

Strany 310

366 QoS Commandswww.dell.com | support.dell.commatch dstl4portUse the match dstl4port command in Class-Map Configuration mode to add to the specified

Strany 311

QoS Commands 367Command ModeClass-Map Configuration modeUser GuidelinesThis command has no user guidelines.ExampleThe following example displays how t

Strany 312

36 Contentsip vrrp preempt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817ip vrrp priority. . . . . . . . . . . . . . . . . . . .

Strany 313 - Line Commands

368 QoS Commandswww.dell.com | support.dell.commatch ip precedenceUse the match ip precedence command in Class-Map Configuration mode to add to the sp

Strany 314

QoS Commands 369Default ConfigurationThis command has no default configuration.Command ModeClass-Map Configuration modeUser GuidelinesThe ip dscp, ip

Strany 315 - Line Commands 297

370 QoS Commandswww.dell.com | support.dell.comExampleThe following example displays adding a match condition based on the "ip" protocol nam

Strany 316

QoS Commands 371•ipmask—Specifies a valid IP address bit mask. Note that although this IP address bit mask is similar to a subnet mask, it does not ne

Strany 317

372 QoS Commandswww.dell.com | support.dell.comExampleThe following example displays how to add a match condition using the "snmp" port name

Strany 318 - 300 Line Commands

QoS Commands 373Command ModePolicy-Class-Map Configuration modeUser GuidelinesThe port identified in this command is identical to the destination port

Strany 319 - IP Addressing Commands

374 QoS Commandswww.dell.com | support.dell.comUser GuidelinesOnly one style of police command (simple) is allowed for a given class instance in a par

Strany 320

QoS Commands 375redirectUse the redirect command in Policy-Class-Map Configuration mode to specify that all incoming packets for the associated traffi

Strany 321 - IP Addressing Commands 303

376 QoS Commandswww.dell.com | support.dell.comInterface Configuration (Ethernet, Port-channel) mode (for a specific interface)User GuidelinesThis co

Strany 322

QoS Commands 377Source Layer 4 Port 234show classofservice dot1p-mappingUse the show classofservice dot1p-mapping command in Privileged EXEC

Strany 323 - IP Addressing Commands 305

Command Groups 1Command GroupsIntroductionThe Command Line Interface (CLI) is a network management application operated through an ASCII terminal with

Strany 324

378 QoS Commandswww.dell.com | support.dell.comThe following table lists the parameters in the example and gives a description of each.show classofser

Strany 325 - IP Addressing Commands 307

QoS Commands 379 7 1 8(cs1) 0 9 0 10(af11) 0 11 0 12(af12)

Strany 326

380 QoS Commandswww.dell.com | support.dell.com 35 2 36(af42) 2 37 2 38(af43) 2 39

Strany 327 - IP Addressing Commands 309

QoS Commands 381 63 3console#show classofservice trustUse the show classofservice trust command in Privileged EXEC mode to display

Strany 328

382 QoS Commandswww.dell.com | support.dell.comSyntaxshow diffservDefault ConfigurationThis command has no default configuration.Command ModePrivilege

Strany 329

QoS Commands 383Exampleconsole#show diffserv service interface ethernet 1/g1 inDiffServ Admin Mode... EnableInterface...

Strany 330

384 QoS Commandswww.dell.com | support.dell.comSyntaxshow diffserv service briefDefault ConfigurationThis command has no default configuration.Command

Strany 331 - 802.1x Commands

QoS Commands 385User GuidelinesIf the interface is specified, the class-of-service queue configuration of the interface is displayed. If omitted, the

Strany 332

386 QoS Commandswww.dell.com | support.dell.comThe following table lists the parameters in the examples and gives a description of each.show policy-ma

Strany 333 - 802.1x Commands 317

QoS Commands 387User GuidelinesThis command has no user guidelines.ExampleThe following example displays the DiffServ information.console#show policy-

Strany 334

2 ContentsIP Addressing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 17802.1x Commands. . . . . . . . . . . . . . . . . . . . . . .

Strany 335 - 802.1x Commands 319

2 Command Groupswww.dell.com | support.dell.comDHCP Filtering Configures DHCP filtering and whether an interface is trusted for filtering.Ethernet Con

Strany 336

388 QoS Commandswww.dell.com | support.dell.comClass Name... muraliIn Discarded Packets... 0

Strany 337 - 802.1x Commands 321

QoS Commands 3891/g5 Down DELL1/g6 Down DELL1/g7 Down DELL1/g8 Down DELL1/g9 Down DELL1/g10 Down DELLtraffic-shapeUse the traffic-sha

Strany 338

390 QoS Commandswww.dell.com | support.dell.com

Strany 339

Radius Commands 393Radius Commandsauth-portUse the auth-port command in Radius mode to set the port number for authentication requests of the designat

Strany 340

394 Radius Commandswww.dell.com | support.dell.comSyntaxdeadtime deadtime •deadtime—The amount of time that the unavailable server is skipped over.

Strany 341

Radius Commands 395ExampleThe following example specifies an authentication and encryption key of "lion-king".console(config)#radius-server

Strany 342

396 Radius Commandswww.dell.com | support.dell.com•deadtime—Length of time in minutes, for which a Radius server is skipped over by transaction reques

Strany 343

Radius Commands 397ExampleThe following example specifies a Radius server host with the following characteristics:• Server host IP address—192.168.10.

Strany 344 - 802.1 Advanced Features

398 Radius Commandswww.dell.com | support.dell.comno radius-server retransmit•retries—Specifies the retransmit value. (Range: 1 - 10)Default Configura

Strany 345 - 802.1x Commands 329

Radius Commands 399ExampleThe following example configures the source IP address used for communication with Radius servers to 10.1.1.1.console(config

Strany 346

Command Groups 3Telnet Server Configures Telnet service on the switch and displays Telnet information.802.1x Configures and displays commands related

Strany 347 - 802.1x Commands 331

400 Radius Commandswww.dell.com | support.dell.comDefault ConfigurationThe default number for attempts is 3.Command Mode Radius modeUser GuidelinesUse

Strany 348

Radius Commands 401Global Values--------------TimeOut : 3Retransmit : 3Deadtime : 0Source IP : 1.2.3.4source-ipUse the source-ip command in Radius mod

Strany 349

402 Radius Commandswww.dell.com | support.dell.comDefault ConfigurationThe default value is 3 seconds.Command ModeRadius modeUser GuidelinesUser must

Strany 350

RMON Commands 405RMON Commandsrmon alarmUse the rmon alarm command in Global Configuration mode to configure alarm conditions. To remove an alarm, use

Strany 351

406 RMON Commandswww.dell.com | support.dell.com•startup direction—The alarm that may be sent when this entry is first set to valid. If the first samp

Strany 352

RMON Commands 407no rmon collection history index•index—The requested statistics index group. (Range: 1 - 65535)•owner ownername—Records the RMON stat

Strany 353

408 RMON Commandswww.dell.com | support.dell.com•community text—If an SNMP trap is to be sent, it is sent to the SNMP community specified by this octe

Strany 354

RMON Commands 409User GuidelinesThe configured table size is effective after the device is rebooted.ExampleThe following example configures the maximu

Strany 355

410 RMON Commandswww.dell.com | support.dell.comRising Event: 1Falling Event: 1Owner: CLIThe following table describes the significant fields shown in

Strany 356

RMON Commands 411Syntaxshow rmon alarm-tableDefault ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesTh

Strany 357

4 Command Groupswww.dell.com | support.dell.comMode TypesThe tables on the following pages use these abbreviations for Command Mode names.• CC — Crypt

Strany 358

412 RMON Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser Guidelin

Strany 359

RMON Commands 413Default ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser GuidelinesThis command has no user guid

Strany 360

414 RMON Commandswww.dell.com | support.dell.com•index—The requested set of samples. (Range: 1 - 65535)•throughput—Displays throughput counters.•error

Strany 361 - Syntax Description

RMON Commands 415The following example displays RMON Ethernet Statistics history for "other" on index number 1.console> show rmon history

Strany 362

416 RMON Commandswww.dell.com | support.dell.comshow rmon logUse the show rmon log command in User EXEC mode to display the RMON logging table.Syntaxs

Strany 363

RMON Commands 417User GuidelinesThis command has no user guidelines.ExampleThe following examples display the RMON logging table.console> show rmon

Strany 364

418 RMON Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModeUser EXEC modeUser Guidelin

Strany 365 - QoS Commands

RMON Commands 419Multicast The total number of good packets received and directed to a Multicast address. This number does not include packets directe

Strany 366

420 RMON Commandswww.dell.com | support.dell.com

Strany 367 - QoS Commands 355

SNMP Commands 421SNMP Commandsshow snmpUse the show snmp command in Privileged EXEC mode to display the SNMP communications status.Syntaxshow snmpDefa

Strany 368

Command Groups 5Layer 2 CommandsManagement ACL CommandsUser Interface CommandsAAA CommandsCommand Description Mode*deny (management) Defines a deny ru

Strany 369 - QoS Commands 357

422 SNMP Commandswww.dell.com | support.dell.comCommunity-String Group name IP address---------------- --------- ----------public user-gr

Strany 370

SNMP Commands 423Command ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe following example displays the SNMP eng

Strany 371 - QoS Commands 359

424 SNMP Commandswww.dell.com | support.dell.comExampleThe following examples display the configuration of filters with and without a filter name spec

Strany 372

SNMP Commands 425ExampleThe following examples display the configuration of views.console# show snmp groups Name Security

Strany 373 - QoS Commands 361

426 SNMP Commandswww.dell.com | support.dell.comshow snmp usersUse the show snmp users Privileged EXEC command to display the configuration of users.S

Strany 374

SNMP Commands 427bob user-group MD5 DES 800002a20300fce3900106show snmp viewsUse the show snmp views command in Privileged EXEC

Strany 375

428 SNMP Commandswww.dell.com | support.dell.comExampleThe following examples display the configuration of views with and without a view name specifie

Strany 376

SNMP Commands 429•su—Indicates SNMP administrator access.•ipaddress—Specifies the IP address of the management station. If no IP address is specified,

Strany 377 - QoS Commands 365

430 SNMP Commandswww.dell.com | support.dell.com• ip-address—Management station IP address. Default is all IP addresses.Default ConfigurationNo commun

Strany 378

SNMP Commands 431ExampleThe following example displays setting up the system contact point as "Dell_Technical_Support".console(config)# snmp

Strany 379 - QoS Commands 367

6 Command Groupswww.dell.com | support.dell.comAddress Table Commandsip https authentication Specifies authentication methods for https. GClogin authe

Strany 380

432 SNMP Commandswww.dell.com | support.dell.comSyntaxsnmp-server engineID local {engineid-string | default }no snmp-server engineID local• engineid-s

Strany 381 - QoS Commands 369

SNMP Commands 433Syntaxsnmp-server filter filter-name oid-tree {included | excluded}no snmp-server filter filter-name [oid-tree]•filter-name—Specifies

Strany 382

434 SNMP Commandswww.dell.com | support.dell.comsnmp-server groupUse the snmp-server group command in Global Configuration mode to configure a new Sim

Strany 383 - QoS Commands 371

SNMP Commands 435User GuidelinesView-name should be an existing view created using the snmp-server view command. If there are multiple records with th

Strany 384

436 SNMP Commandswww.dell.com | support.dell.comDefault ConfigurationThe default configuration is 3 retries, and 15 seconds timeout.Command ModeGlobal

Strany 385 - QoS Commands 373

SNMP Commands 437snmp-server trap authenticationUse the snmp-server trap authentication command in Global Configuration mode to enable the switch to s

Strany 386

438 SNMP Commandswww.dell.com | support.dell.com•engineid-string—Specifies the engine ID of the remote SNMP entity to which the user belongs. The engi

Strany 387 - QoS Commands 375

SNMP Commands 439snmp-server viewUse the snmp-server view command in Global Configuration mode to create or update a Simple Network Management Protoco

Strany 388

440 SNMP Commandswww.dell.com | support.dell.comSyntaxsnmp-server v3-host {ip-address | hostname} username {traps | informs} [noauth | auth | priv] [t

Strany 389

Port Channel Commands 441Port Channel Commandschannel-groupUse the channel-group command in Interface Configuration mode to configure a port-to-port c

Strany 390

Command Groups 7Clock Commandsshow bridge address-table count Displays the number of addresses present in the Forwarding Database.PEshow bridge addres

Strany 391 - QoS Commands 379

442 Port Channel Commandswww.dell.com | support.dell.cominterface port-channelUse the interface port-channel command in Global Configuration mode to c

Strany 392

Port Channel Commands 443User GuidelinesCommands in the interface range context are executed independently on each interface in the range. If the comm

Strany 393

444 Port Channel Commandswww.dell.com | support.dell.comconsole(config-if-ch1)#hashing-mode 4no hashing-modeUse the no hashing-mode command to set the

Strany 394

Port Channel Commands 445ExampleConsole#show interfaces port-channelChannel Ports Hashing-mode------- --------

Strany 395 - QoS Commands 383

446 Port Channel Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe

Strany 396 - 1/g1 in Down DELL

Port Channel Commands 447Overruns... 0Total Received Packets Not Forwarded... 0Local Traffic Frames...

Strany 397

448 Port Channel Commandswww.dell.com | support.dell.comGVRP Failed Registrations... 0Time Since Counters Last Cleared...

Strany 398

Spanning Tree Commands 449Spanning Tree Commandsabort (mst)Use the abort command in MST mode to exit the MST region configuration mode without applyin

Strany 399 - QoS Commands 387

450 Spanning Tree Commandswww.dell.com | support.dell.comSyntaxclear spanning-tree detected-protocols [ethernet interface| port-channel port-channel-n

Strany 400

Spanning Tree Commands 451ExampleThe following example shows how to exit the MST configuration mode and save changes. console(config)#spanning-tree ms

Strany 401

8 Command Groupswww.dell.com | support.dell.comDenial of Service CommandsDHCP Filtering Commandsno clock summer-time recurring Resets the recurring s

Strany 402 - 390 QoS Commands

452 Spanning Tree Commandswww.dell.com | support.dell.comSyntaxname string•string—Case sensitive MST configuration name. (Range: 1-32 characters)Defau

Strany 403 - Radius Commands

Spanning Tree Commands 453ExampleThe following example sets the configuration revision to 1.console(config)#spanning-tree mst configurationconsole(con

Strany 404

454 Spanning Tree Commandswww.dell.com | support.dell.comshow spanning-treeUse the show spanning-tree command in Privileged EXEC mode to display the s

Strany 405 - Radius Commands 395

Spanning Tree Commands 455Bridge ID Priority 36864Address 00:02:4b:29:7a:00 Hello Time 2 sec Max Age 20 sec Forward Delay 15 secI

Strany 406

456 Spanning Tree Commandswww.dell.com | support.dell.com Root Port 1(1/g1) Hello Time 2 sec Max Age 20 sec Forward Delay 15

Strany 407 - Radius Commands 397

Spanning Tree Commands 4571/g4 Enabled 128.4 20000 BLK Altn No console#show spanning-tree blockedportsSpanning tree enabled mode R

Strany 408

458 Spanning Tree Commandswww.dell.com | support.dell.comTimes: hold 1, hello 2, max age 20, forward delay 15Port 1 (1/g1) enabledState: Forwarding

Strany 409 - Radius Commands 399

Spanning Tree Commands 459Designated port id: 128.25 Designated path cost: 20000BPDU: sent 2, received 120638console#show spanning-tree ethe

Strany 410

460 Spanning Tree Commandswww.dell.com | support.dell.com1/g3 Enabled 128.3 20000 FWD Desg No 1/g4 Enabled 128.4 20000 FWD Desg

Strany 411

Spanning Tree Commands 461Port id: 128.1 Port cost: 20000Port Fast: No (configured:no)Designated bridge Priority: 32768

Strany 412

Command Groups 9Ethernet Configuration CommandsCommand Description Mode*clear counters Clears statistics on an interface. PEdescription Adds a descrip

Strany 413 - RMON Commands

462 Spanning Tree Commandswww.dell.com | support.dell.com Path Cost 20000 Port Cost 4 (1/g4)

Strany 414

Spanning Tree Commands 463BPDU: sent 2, received 170638console#show spanning-treeSpanning tree enabled mode MSTP######MST 0 Vlans Mapped: 1-9, 21-4094

Strany 415

464 Spanning Tree Commandswww.dell.com | support.dell.comSyntaxspanning-tree bpdu {filtering | flooding}no spanning-tree bpdu•filtering—Filter BPDU pa

Strany 416

Spanning Tree Commands 465Default ConfigurationBPDU protection is not enabled.Command ModeGlobal Configuration modeUser GuidelinesThis command has no

Strany 417 - RMON Commands 409

466 Spanning Tree Commandswww.dell.com | support.dell.comExampleThe following example configures the spanning-tree cost on 1/g5 to 35000.console(confi

Strany 418

Spanning Tree Commands 467Default ConfigurationThe default forwarding-time for IEEE Spanning-tree Protocol (STP) is 15 seconds.Command Modes Global Co

Strany 419 - OID Monitored variable OID

468 Spanning Tree Commandswww.dell.com | support.dell.comspanning-tree max-ageUse the spanning-tree max-age command in Global Configuration mode to co

Strany 420

Spanning Tree Commands 469Default ConfigurationRapid Spanning Tree Protocol (RSTP) is supported.Command Mode Global Configuration modeUser GuidelinesI

Strany 421

470 Spanning Tree Commandswww.dell.com | support.dell.comspanning-tree mst costUse the spanning-tree mst cost command in Interface Configuration mode

Strany 422

Spanning Tree Commands 471Syntaxspanning-tree mst max-hops hop-countno spanning-tree mst max-hops•hop-count—Number of hops in an MST region before the

Strany 423

10 Command Groupswww.dell.com | support.dell.comGVRP CommandsIGMP Snooping CommandsCommand Description Mode*clear gvrp statistics Clears all the GVRP

Strany 424

472 Spanning Tree Commandswww.dell.com | support.dell.comExampleThe following example configures the port priority of port 1/g1 to 144.console(config)

Strany 425

Spanning Tree Commands 473Syntaxspanning-tree portfastno spanning-tree portfastDefault ConfigurationPortFast mode is disabled.Command Mode Interface C

Strany 426

474 Spanning Tree Commandswww.dell.com | support.dell.comUser GuidelinesThe priority value must be a multiple of 16.ExampleThe following example confi

Strany 427

Spanning Tree Commands 475Due to configuration error of the maintenance personnel or a malicious user attack, a designated root of the network may rec

Strany 428 - 420 RMON Commands

476 Spanning Tree Commandswww.dell.com | support.dell.com

Strany 429 - SNMP Commands

SSH Commands 479SSH Commandscrypto key generate dsaUse the crypto key generate dsa command in Global Configuration mode to generate DSA key pairs for

Strany 430

480 SSH Commandswww.dell.com | support.dell.comcrypto key generate rsaUse the crypto key generate rsa command in Global Configuration mode to generate

Strany 431 - SNMP Commands 423

SSH Commands 481ExampleThe following example enters the SSH Public Key-chain configuration mode.console(config)#crypto key pubkey-chain sshconsole(con

Strany 432

482 SSH Commandswww.dell.com | support.dell.comip ssh pubkey-authUse the ip ssh pubkey-auth command in Global Configuration mode to enable public key

Strany 433 - SNMP Commands 425

SSH Commands 483ExampleThe following example enables the switch to be configured using SSH.console(config)#ip ssh serverkey-stringUse the key-string S

Strany 434

Command Groups 11IGMP Snooping Querier CommandsLACP Commandsip igmp snooping fast-leave Enables or disables IGMP Snooping fast-leave mode on a selecte

Strany 435

484 SSH Commandswww.dell.com | support.dell.com+Z4TrEU/9FJxwPiVQOjc+KBXuR0juNg5nFYsY0ZCk0N/W9a/tnkm1shRE7Di71+w3fNiOA6w9o44t6+AINEICBCCA4YcF6zMzaT1wef

Strany 436

SSH Commands 485R2VaSN/WC0IK53j9re4B11AE+O3qAxwJs0KD7cTkvF9I+YdiXeOM8VE4skkwAiyLDNVWXgNQ6iat8+8Mjth+PIo5t3HykYUCkD8B1v93nzi/sr4hHHJCdx7wwRW3QtgXaGwYt2

Strany 437

486 SSH Commandswww.dell.com | support.dell.comThe following example displays the SSH public called "dana."console#show crypto key pubkey-ch

Strany 438

SSH Commands 487user-keyUse the user-key command in SSH Public Key Chain Configuration mode to specify which SSH public key you are configuring manual

Strany 439 - SNMP Commands 431

488 SSH Commandswww.dell.com | support.dell.com

Strany 440

Syslog Commands 489Syslog Commandsclear loggingUse the clear logging command in Privileged EXEC mode to clear messages from the internal logging buffe

Strany 441

490 Syslog Commandswww.dell.com | support.dell.comDefault ConfigurationThere is no default configuration for the command.Command ModePrivileged EXECUs

Strany 442

Syslog Commands 491Syntaxlevel levelno level•level—The level number for syslog messages. (Range: emergency, alert, critical, error, warning, notice, i

Strany 443

492 Syslog Commandswww.dell.com | support.dell.com<189> JAN 13 05:20:27 192.168.2.1-1 UNKN[248900192]: cmd_logger_api.c(87) 2113 %% CLI:EIA-232:

Strany 444

Syslog Commands 493logging bufferedUse the logging buffered command in Global Configuration mode to limit syslog messages displayed from an internal b

Strany 445 - SNMP Commands 437

Contents 3PIM-DM Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44PIM-SM Commands. . . . . . . . . . . . . . . . . . . . . . . .

Strany 446

12 Command Groupswww.dell.com | support.dell.comLink Dependency CommandsLLDP CommandsCommand Description Mode*link-dependency group Enters the link-d

Strany 447

494 Syslog Commandswww.dell.com | support.dell.comDefault ConfigurationThe default number of messages is 200.Command ModeGlobal Configuration modeUser

Strany 448

Syslog Commands 495logging facilityUse the logging facility command in Global Configuration mode to set the facility for logging messages. To reset to

Strany 449 - Port Channel Commands

496 Syslog Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following example limits syslog messag

Strany 450

Syslog Commands 497Syntaxport portno port• port—The port number for syslog messages. (Range: 1-65535)Default ConfigurationThe default port number is 5

Strany 451 - Port Channel Commands 443

498 Syslog Commandswww.dell.com | support.dell.comLogging is enabled.Console logging: level debugging. console Messages: 0 Dropped.Buffer logging: lev

Strany 452

Syslog Commands 49911-Aug-2005 15:41:39: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet g1, changed state to up11-Aug-2005 15:41:39: %

Strany 453

500 Syslog Commandswww.dell.com | support.dell.comshow syslog-serversUse the show syslog-servers command in Privileged EXEC mode to display the syslog

Strany 454

TACACS+ Commands 503TACACS+ CommandskeyUse the key command in TACACS Configuration mode to specify the authentication and encryption key for all TACAC

Strany 455 - Port Channel Commands 447

504 TACACS+ Commandswww.dell.com | support.dell.com•port-number—The server port number. If left unspecified, the default port number is 49. (Range: 0

Strany 456 - 448 Port Channel Commands

TACACS+ Commands 505show tacacsUse the show tacacs command in Privileged EXEC mode to display the configuration and statistics of a TACACS+ server.Syn

Strany 457 - Spanning Tree Commands

Command Groups 13Password Managementlldp transmit Enables the LLDP advertise capability. IClldp transmit-mgmt Specifies that transmission of the local

Strany 458

506 TACACS+ Commandswww.dell.com | support.dell.comDefault ConfigurationNo TACACS+ host is specified.Command ModeGlobal Configuration modeUser Guideli

Strany 459 - Spanning Tree Commands 451

TACACS+ Commands 507tacacs-server timeoutUse the tacacs-server timeout command in Global Configuration mode to set the interval during which a switch

Strany 460

508 TACACS+ Commandswww.dell.com | support.dell.comExampleThis example shows how to specify the timeout value.console(config-tacacs)#timeout 23

Strany 461 - Spanning Tree Commands 453

Telnet Server Commands 509Telnet Server Commandsip telnet server disableThis command is used to enable/disable the Telnet service on the switch.ip tel

Strany 462

510 Telnet Server Commandswww.dell.com | support.dell.comSyntaxip telnet port port number•port number—Telnet service port number (Range: 1–65535)Defau

Strany 463

VLAN Commands 511VLAN Commandsdvlan-tunnel ethertypeUse the dvlan-tunnel ethertype command in Global Configuration mode to configure the ethertype for

Strany 464 - 456 Spanning Tree Commands

512 VLAN Commandswww.dell.com | support.dell.cominterface vlanUse the interface vlan command in Global Configuration mode to configure a VLAN type and

Strany 465

VLAN Commands 513User GuidelinesCommands used in the interface range context are executed independently on each interface in the range. If the command

Strany 466 - 458 Spanning Tree Commands

514 VLAN Commandswww.dell.com | support.dell.comSyntaxname stringno name•string—Comment or description to help identify a specific VLAN (Range: 1 - 32

Strany 467

VLAN Commands 515Default ConfigurationThis command has no default configuration.Command ModeVLAN Database modeUser GuidelinesThis command has no user

Strany 468 - 460 Spanning Tree Commands

14 Command Groupswww.dell.com | support.dell.comPort Monitor CommandsPHY Diagnostics CommandsSystem Management CommandsCommand Description Mode*monito

Strany 469

516 VLAN Commandswww.dell.com | support.dell.comCommand ModeInterface Configuration (Ethernet) modeUser GuidelinesThis command has no user guidelines.

Strany 470 - 462 Spanning Tree Commands

VLAN Commands 517ExampleThe following example displays how to add all physical interfaces to the protocol-based group identified by group ID "2.&

Strany 471

518 VLAN Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe followin

Strany 472

VLAN Commands 519Command ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExamplesThe following example displays switchport

Strany 473 - Spanning Tree Commands 465

520 VLAN Commandswww.dell.com | support.dell.comThe following example displays switchport configuration individually for 1/g2.console#show interface s

Strany 474

VLAN Commands 521Static configuration:PVID: 2922Ingress Filtering: EnabledAcceptable Frame Type: UntaggedGVRP status: DisabledPort 2/g19 is member in:

Strany 475 - Spanning Tree Commands 467

522 VLAN Commandswww.dell.com | support.dell.comshow switchport protectedUse the show switchport protected command in Privileged EXEC mode to display

Strany 476

VLAN Commands 523ExampleThe following example displays all VLAN information.console#show vlanVLAN Name Ports Type Auth

Strany 477 - Spanning Tree Commands 469

524 VLAN Commandswww.dell.com | support.dell.com----------------------- -------0001.0001.0001.0001 1console#show vlan association subnetUse the sh

Strany 478

VLAN Commands 525switchport access vlanUse the switchport access vlan command in Interface Configuration mode to configure the VLAN ID when the interf

Strany 479 - Spanning Tree Commands 471

Command Groups 15no cut-through mode Disables the cut-through mode on the switch. GCno standby Unconfigures the standby in the stack. Stack GCping Sen

Strany 480

526 VLAN Commandswww.dell.com | support.dell.com•remove vlan-list—List of valid VLAN IDs to remove from the forbidden list. Separate nonconsecutive VL

Strany 481 - Spanning Tree Commands 473

VLAN Commands 527console(config-if-1/g8)#switchport general acceptable-frame-type tagged-onlyswitchport general allowed vlanUse the switchport general

Strany 482

528 VLAN Commandswww.dell.com | support.dell.comSyntaxswitchport general ingress-filtering disableno switchport general ingress-filtering disableDefau

Strany 483

VLAN Commands 529ExampleThe following example shows how to configure the PVID for 1/g8, when the interface is in general mode.console(config)#interfac

Strany 484 - 476 Spanning Tree Commands

530 VLAN Commandswww.dell.com | support.dell.comswitchport protectedUse the switchport protected command in Interface Configuration mode to configure

Strany 485 - SSH Commands

VLAN Commands 531Default ConfigurationThis command has no default configuration.Command ModeGlobal Configuration modeUser GuidelinesThis command has n

Strany 486

532 VLAN Commandswww.dell.com | support.dell.comvlanUse the vlan command in VLAN Database mode to configure a VLAN. To delete a VLAN, use the no form

Strany 487

VLAN Commands 533Default ConfigurationNo assigned MAC address.Command ModeVLAN Database modeUser GuidelinesThis command has no user guidelines.Example

Strany 488

534 VLAN Commandswww.dell.com | support.dell.comvlan databaseUse the vlan database command in Global Configuration mode to enter the VLAN database con

Strany 489 - SSH Commands 483

VLAN Commands 535User GuidelinesThe dynamic VLAN (created via GRVP) should exist prior to executing this command. See the Type column in output from t

Strany 490

16 Command Groupswww.dell.com | support.dell.comACL CommandsLine CommandsCommand Description Mode*access-list Creates an Access Control List (ACL) tha

Strany 491

536 VLAN Commandswww.dell.com | support.dell.comvlan protocol group add protocolUse the vlan protocol group add protocol command in Global Configurati

Strany 492

VLAN Commands 537•groupid—The protocol-based VLAN group ID, which is automatically generated when you create a protocol-based VLAN group with the vlan

Strany 493

538 VLAN Commandswww.dell.com | support.dell.com

Strany 494 - 488 SSH Commands

Web Server Commands 541Web Server Commandscommon-nameUse the common-name command in Crypto Certificate Generation or Crypto Certificate Request mode t

Strany 495 - Syslog Commands

542 Web Server Commandswww.dell.com | support.dell.comSyntaxcountry country•country—Specifies the country name. (Range: 2 characters)Default Configura

Strany 496

Web Server Commands 543ExampleThe following example generates a self-signed HTTPS certificate.console(config)#crypto certificate 1 generateconsole(con

Strany 497 - Syslog Commands 491

544 Web Server Commandswww.dell.com | support.dell.comnnH/xQSGA2ffkRBwU2XIxb7n8VPsTm1xyJ1t11a1GaqchfMqqe0kmfhcoHSWryf1FpD0MWOTgDAwIDAQABo4IBojCCAZ4wEw

Strany 498

Web Server Commands 545After receiving the certificate from the Certification Authority, use the crypto certificate import command in Global Configura

Strany 499 - Syslog Commands 493

546 Web Server Commandswww.dell.com | support.dell.comCommand ModeCrypto Certificate Generation modeUser GuidelinesThis command mode is entered using

Strany 500

Web Server Commands 547Syntaxip http serverno ip http serverDefault ConfigurationThe default mode is enabled.Command ModeGlobal Configuration modeUser

Strany 501 - Syslog Commands 495

Command Groups 17IP Addressing Commands802.1x CommandsCommand Description Mode*clear host Deletes entries from the host name-to-address cache PEhelper

Strany 502

548 Web Server Commandswww.dell.com | support.dell.comip https portUse the ip https port command in Global Configuration mode to configure a TCP port

Strany 503 - Syslog Commands 497

Web Server Commands 549User GuidelinesYou must use the crypto certificate generate command to generate the HTTPS certificate.ExampleThe following exam

Strany 504

550 Web Server Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModeCrypto Certificate Ge

Strany 505

Web Server Commands 551show crypto certificate mycertificateUse the show crypto certificate mycertificate command in Privileged EXEC mode to view the

Strany 506

552 Web Server Commandswww.dell.com | support.dell.comshow ip httpUse the show ip http command in Privileged EXEC mode to display the HTTP server conf

Strany 507 - TACACS+ Commands

Web Server Commands 553ExampleThe following example displays the HTTPS server configuration with DH Key exchange enabled.console#show ip httpsHTTPS se

Strany 508

554 Web Server Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModeCrypto Certificate Ge

Strany 509 - TACACS+ Commands 505

Layer 3 Commands 557Layer 3 CommandsThe chapters that follow describe commands that conform to the OSI model’s Network Layer (Layer 3). Layer 3 comman

Strany 510

558 Layer 3 Commandswww.dell.com | support.dell.com

Strany 511 - TACACS+ Commands 507

ARP Commands 559ARP Commands arpUse the arp command in Global Configuration mode to create an Address Resolution Protocol (ARP) entry. Use the no form

Strany 512 - 508 TACACS+ Commands

18 Command Groupswww.dell.com | support.dell.comdot1x port-control Enables manual control of the authorization state of the port.ICdot1x re-authentica

Strany 513 - Telnet Server Commands

560 ARP Commandswww.dell.com | support.dell.comSyntaxarp cachesize integer no arp cachesize•integer—Maximum number of ARP entries in the cache. (Range

Strany 514

ARP Commands 561console(config)#no arp dynamic renewarp purgeUse the arp purge command in Privileged EXEC mode to cause the specified IP address to be

Strany 515 - VLAN Commands

562 ARP Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following example defines a response time

Strany 516

ARP Commands 563Default ConfigurationThe default value is 1200 seconds.Command ModeGlobal Configuration modeUser GuidelinesThis command has no user gu

Strany 517 - VLAN Commands 513

564 ARP Commandswww.dell.com | support.dell.commay also respond if the target IP address is reachable. The device only responds if all next hops in it

Strany 518

ARP Commands 565ExampleThe following example shows show arp command output.console#show arpAge Time (seconds)... 1200Respons

Strany 519 - VLAN Commands 515

566 ARP Commandswww.dell.com | support.dell.com

Strany 520

DHCP and BOOTP Relay Commands 567DHCP and BOOTP Relay Commandsbootpdhcprelay cidridoptmodeUse the bootpdhcprelay cidridoptmode command in Global Confi

Strany 521 - VLAN Commands 517

568 DHCP and BOOTP Relay Commandswww.dell.com | support.dell.comSyntaxbootpdhcprelay enable no bootpdhcprelay enableDefault ConfigurationDisabled is t

Strany 522

DHCP and BOOTP Relay Commands 569ExampleThe following example defines a maximum hopcount of 6.console(config)#bootpdhcprelay maxhopcount 6bootpdhcprel

Strany 523

Command Groups 19Configuration and Image Files CommandsQoS CommandsCommand Description Mode*boot system Specifies the system image that the switch loa

Strany 524 - 520 VLAN Commands

570 DHCP and BOOTP Relay Commandswww.dell.com | support.dell.com•ip-address—IP address of the BootP/DHCP Relay serverDefault Configuration0.0.0.0 is t

Strany 525

DHCP and BOOTP Relay Commands 571Circuit Id and Remote Agent ID Option Mode... EnableRequests Received... 0Requests Relay

Strany 526

572 DHCP and BOOTP Relay Commandswww.dell.com | support.dell.com

Strany 527

DHCPv6 Commands 573DHCPv6 Commands clear ipv6 dhcpUse the clear ipv6 dhcp command in Privileged EXEC mode to clear DHCPv6 statistics for all interface

Strany 528

574 DHCPv6 Commandswww.dell.com | support.dell.comno dns-server dns-server-address•dns-server-address—Valid IPv6 address. Default ConfigurationThis co

Strany 529 - VLAN Commands 525

DHCPv6 Commands 575ExampleThe following example sets the DNS domain name "test", which is provided to a DHCPv6 client by the DHCPv6 server.c

Strany 530

576 DHCPv6 Commandswww.dell.com | support.dell.comSyntaxipv6 dhcp relay {destination relay-address [interface vlan vlan-id] | interface vlan vlan-id}[

Strany 531

DHCPv6 Commands 577•option—Agent information option. (Range: 32-65535)Default Configuration32 is the default value for option. Command ModeGlobal Conf

Strany 532

578 DHCPv6 Commandswww.dell.com | support.dell.comipv6 dhcp serverUse the ipv6 dhcp server command in Interface Configuration mode to configure DHCPv6

Strany 533 - VLAN Commands 529

DHCPv6 Commands 579•DUID—Client DUID (e.g. 00:01:00:09:f8:79:4e:00:04:76:73:43:76').•hostname—Client hostname used for logging and tracing. (Rang

Strany 534

20 Command Groupswww.dell.com | support.dell.comclass-map Defines a new DiffServ class of type match-all, match-any, or match-access-group. For now, o

Strany 535 - VLAN Commands 531

580 DHCPv6 Commandswww.dell.com | support.dell.comExampleThe following example enables DHCPv6 globally.console#configureconsole(config)#service dhcpv6

Strany 536

DHCPv6 Commands 581Default ConfigurationThis command has no default configuration.Command Mode Privileged EXEC mode User GuidelinesThis command has n

Strany 537 - VLAN Commands 533

582 DHCPv6 Commandswww.dell.com | support.dell.comRelay Address... 2020:1::1Relay Interface Number...

Strany 538

DHCPv6 Commands 583show ipv6 dhcp poolUse the show ipv6 dhcp pool command in Privileged EXEC mode to display the configured DHCP pool.Syntaxshow ipv6

Strany 539 - VLAN Commands 535

584 DHCPv6 Commandswww.dell.com | support.dell.comExampleThe following example displays the DHCPv6 server name and status.console> show ipv6 dhcp s

Strany 540

DVMRP Commands 587DVMRP Commands ip dvmrpUse the ip dvmrp command to set the administrative mode of DVMRP in the router to active. IGMP must be enable

Strany 541

588 DVMRP Commandswww.dell.com | support.dell.comSyntaxip dvmrp metric metricno ip dvmrp metric•metric—Cost to reach the network. (Range: 1-31)Default

Strany 542 - 538 VLAN Commands

DVMRP Commands 589console#configureconsole(config)#ip dvmrp trapflagsconsole(config)#no ip dvmrp trapflagsshow ip dvmrpUse the show ip dvmrp command i

Strany 543 - Web Server Commands

590 DVMRP Commandswww.dell.com | support.dell.comSyntaxshow ip dvmrp interface vlan-id•vlan-id—Valid VLAN ID.Default ConfigurationThis command has no

Strany 544

DVMRP Commands 591show ip dvmrp nexthopUse the show ip dvmrp nexthop command in Privileged EXEC mode to display the next hop information on outgoing i

Strany 545 - Web Server Commands 543

Command Groups 21match dstl4port Adds to the specified class definition a match condition based on the destination layer 4 port of a packet using a si

Strany 546

592 DVMRP Commandswww.dell.com | support.dell.comExampleThe following example displays the table that lists the router’s upstream prune information. c

Strany 547

IGMP Commands 595IGMP Commands ip igmpUse the ip igmp command in Global Configuration mode to set the administrative mode of IGMP in the system to act

Strany 548

596 IGMP Commandswww.dell.com | support.dell.comSyntaxip igmp last-member-query-count countno ip igmp last-member-query-count•count—Query count. (Rang

Strany 549 - Web Server Commands 547

IGMP Commands 597User GuidelinesThis command has no user guidelines.ExampleThe following example configures 2 seconds as the Maximum Response Time ins

Strany 550

598 IGMP Commandswww.dell.com | support.dell.comSyntaxip igmp query-max-response-time tenthsofsecondsno ip igmp query-max-response-time•tenthsofsecond

Strany 551 - Web Server Commands 549

IGMP Commands 599User GuidelinesThis command has no user guidelines.ExampleThe following example configures a robustness value of 10 for VLAN 15.conso

Strany 552

600 IGMP Commandswww.dell.com | support.dell.comSyntaxip igmp startup-query-interval secondsno ip igmp startup-query-interval•seconds—Startup query in

Strany 553 - Default configuration

IGMP Commands 601console#interface vlan 15console(config-if-vlan15)#ip igmp version 2show ip igmpUse the show ip igmp command in Privileged EXEC mode

Strany 554

602 IGMP Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Gu

Strany 555

IGMP Commands 603Interface Mode... EnableIGMP Version... 3Query Interval (secs)...

Strany 556

4 Contentsexit (configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95exit (EXEC) . . . . . . . . . . . . . . . . . . . . . .

Strany 557 - Layer 3 Commands

22 Command Groupswww.dell.com | support.dell.comRadius Commandsshow classofservice ip-dscp-mappingDisplays the current IP DSCP mapping to internal tra

Strany 558 - 558 Layer 3 Commands

604 IGMP Commandswww.dell.com | support.dell.comconsole(config)#show ip igmp interface membership 224.5.5.5 detail IGMP INTERFACE DETAI

Strany 559 - ARP Commands

IGMP Commands 605ip igmp router-alert-optionalUse the ip igmp router-alert-optional command to set IGMP to not require the Router-Alert field.Syntaxip

Strany 560

606 IGMP Commandswww.dell.com | support.dell.com

Strany 561 - ARP Commands 561

IGMP Proxy Commands 607IGMP Proxy Commands ip igmp-proxyUse the ip igmp-proxy command in Interface Configuration mode to enable the IGMP Proxy on the

Strany 562

608 IGMP Proxy Commandswww.dell.com | support.dell.comSyntaxip igmp-proxy reset-statusDefault ConfigurationThis command has no default configuration.C

Strany 563 - ARP Commands 563

IGMP Proxy Commands 609ExampleThe following example sets 10 seconds as the unsolicited report interval for the IGMP Proxy router.console(config)#inter

Strany 564

610 IGMP Proxy Commandswww.dell.com | support.dell.comExampleThe following example displays a summary of the host interface status parameters.console#

Strany 565 - ARP Commands 565

IGMP Proxy Commands 611Ver Query Rcvd Report Rcvd Report Sent Leave Rcvd Leave Sent--------------------------------------------------------------

Strany 566 - 566 ARP Commands

612 IGMP Proxy Commandswww.dell.com | support.dell.comshow ip igmp-proxy groups detailUse the show ip igmp-proxy groups detail command in Privileged E

Strany 567 - DHCP and BOOTP Relay Commands

IP Routing Commands 613IP Routing CommandsencapsulationUse the encapsulation command in Interface Configuration mode to configure the link layer encap

Strany 568

Command Groups 23RMON Commandsradius-server host Specifies a RADIUS server host. GCradius-server key Sets the authentication and encryption key for a

Strany 569

614 IP Routing Commandswww.dell.com | support.dell.comSyntaxip address ip-address {subnet-mask | prefix-length} [secondary]no ip address ip-address {s

Strany 570

IP Routing Commands 615Syntaxip mtu integer•integer—Specifies the distance (preference) of an individual static route. (Range: 68-1500)Default Configu

Strany 571

616 IP Routing Commandswww.dell.com | support.dell.comExampleThe following example defines the IP address and subnet mask for VLAN 15.console(config)#

Strany 572

IP Routing Commands 617ExampleThe following example identifies the ip-address subnet-mask, next-hop-ip and a preference value of 200.console(config)#i

Strany 573 - DHCPv6 Commands

618 IP Routing Commandswww.dell.com | support.dell.comcommands. Changing the default distance does not update the distance of existing static routes,

Strany 574

IP Routing Commands 619Exampleconsole(config)#ip routingroutingUse the routing command in Interface Configuration mode to enable IPv4 and IPv6 routing

Strany 575 - DHCPv6 Commands 575

620 IP Routing Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following example displays IP summ

Strany 576

IP Routing Commands 621Burned In MAC Address... 00:10:18:82:04:35Network Configuration Protocol Current... NoneManagement

Strany 577 - DHCPv6 Commands 577

622 IP Routing Commandswww.dell.com | support.dell.comSyntaxshow ip protocolsDefault ConfigurationThis command has no default configuration.Command Mo

Strany 578

IP Routing Commands 623176.2.1.1 1Routing Information Sources:Gateway State176.1.1.2 FullExternal Preference: 60Internal Preference: 20show ip routeUs

Strany 579 - DHCPv6 Commands 579

24 Command Groupswww.dell.com | support.dell.comSNMP Commandsshow rmon statistics Displays RMON Ethernet Statistics. UE*NOTE: For the meaning of each

Strany 580

624 IP Routing Commandswww.dell.com | support.dell.comB - BGP Derived, IA - OSPF Inter AreaE1 - OSPF External Type 1, E2 - OSPF External Type 2N1 - OS

Strany 581 - DHCPv6 Commands 581

IP Routing Commands 625show ip route summaryUse the show ip route summary command in Privileged EXEC mode to display the routing table summary.Syntaxs

Strany 582

626 IP Routing Commandswww.dell.com | support.dell.comSyntaxshow ip statsDefault ConfigurationThis command has no default configuration.Command ModeUs

Strany 583 - DHCPv6 Commands 583

IP Routing Commands 627IcmpInMsgs... 3IcmpInErrors... 0IcmpInDestUnreachs...

Strany 584

628 IP Routing Commandswww.dell.com | support.dell.com

Strany 585 - DVMRP Commands

IPv6 Routing Commands 629IPv6 Routing Commands clear ipv6 neighborsUse the clear ipv6 neighbors command in Privileged EXEC mode to clear all entries i

Strany 586

630 IPv6 Routing Commandswww.dell.com | support.dell.comSyntaxclear ipv6 statistics [vlan vlan-id| tunnel tunnel-id | loopback loopback-id]•vlan-id—Va

Strany 587

IPv6 Routing Commands 631•prefix-length—Designates how many of the high-order contiguous bits of the address make up the prefix.• eui64—The optional e

Strany 588

632 IPv6 Routing Commandswww.dell.com | support.dell.comExampleThe following example enables IPv6 routing, which has not been configured with an expli

Strany 589 - DVMRP Commands 591

IPv6 Routing Commands 633Syntaxipv6 mtu mtu no ipv6 mtu •mtu—Is the maximum transmission unit. (Range: 1280-1500)Default ConfigurationThe default MTU

Strany 590

Command Groups 25Port Channel CommandsSpanning Tree CommandsCommand Description Mode*channel-group Associates a port with a port-channel. ICinterface

Strany 591 - IGMP Commands

634 IPv6 Routing Commandswww.dell.com | support.dell.comExampleThe following example sets at 10 the number of duplicate address detection probes trans

Strany 592

IPv6 Routing Commands 635Syntaxipv6 nd ns-interval milliseconds no ipv6 nd ns-interval •milliseconds—Interval duration. (Range: 0, 1000 - 4294967295)D

Strany 593 - IGMP Commands 597

636 IPv6 Routing Commandswww.dell.com | support.dell.comExampleThe following example sets to true the “other stateful configuration” flag in router ad

Strany 594

IPv6 Routing Commands 637The ipv6 nd prefix command will allow you to preconfigure RA prefix values before you configure the associated interface addr

Strany 595 - IGMP Commands 599

638 IPv6 Routing Commandswww.dell.com | support.dell.comSyntaxipv6 nd ra-lifetime seconds no ipv6 nd ra-lifetime •seconds—Lifetime duration. The value

Strany 596

IPv6 Routing Commands 639User GuidelinesThis command has no user guidelines.ExampleThe following example sets the router advertisement time at 5000 mi

Strany 597 - IGMP Commands 601

640 IPv6 Routing Commandswww.dell.com | support.dell.comSyntaxipv6 route ipv6-prefix /prefix-length [interface {tunnel tunnel-id | vlan vlan-id}]next-

Strany 598

IPv6 Routing Commands 641Syntaxipv6 route distance integer no ipv6 route distance integer •integer—Specifies the distance (preference) of an individua

Strany 599

642 IPv6 Routing Commandswww.dell.com | support.dell.comconsole(config)#no ipv6 unicast-routingping ipv6Use ping ipv6 command in Privileged EXEC mode

Strany 600

IPv6 Routing Commands 643workstation. The terminal interface sends three pings to the target station. Use the interface keyword to ping an interface b

Strany 601 - Usage Guidelines

26 Command Groupswww.dell.com | support.dell.comSSH Commandsspanning-tree disable Disables spanning tree on a specific port. ICspanning-tree forward-t

Strany 602 - 606 IGMP Commands

644 IPv6 Routing Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe

Strany 603 - IGMP Proxy Commands

IPv6 Routing Commands 645IPv6 is enabledIPv6 Prefix is ... FE80::2FC:E3FF:FE90:147/128 3FF0:123

Strany 604

646 IPv6 Routing Commandswww.dell.com | support.dell.comloopback 2 Disabledtunnel 1 Disabled 3FFE:1234::1/64 [TENT]show ipv6 nei

Strany 605

IPv6 Routing Commands 647•protocol—Specifies the protocol that installed the routes. Is one of the following keywords: connected, ospf, static.•ipv6-p

Strany 606

648 IPv6 Routing Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe

Strany 607

IPv6 Routing Commands 649ExampleThe following example displays a summary of the routing table.console#show ipv6 route summaryIPv6 Routing Table Summar

Strany 608

650 IPv6 Routing Commandswww.dell.com | support.dell.comExamplesThe following examples show traffic and statistics for IPv6 and ICMPv6, first for all

Strany 609 - IP Routing Commands

IPv6 Routing Commands 651Received Datagrams Locally Delivered... 0Received Datagrams Discarded Due To Header Errors... 0Recei

Strany 610

652 IPv6 Routing Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following example displays IPv6

Strany 611 - IP Routing Commands 615

IPv6 Routing Commands 653traceroute ipv6Use the traceroute ipv6 command in Privileged EXEC mode to discover the routes that packets actually take when

Strany 612

Command Groups 27Syslog Commandskey-string Manually specifies a SSH public key. SKshow crypto key mypubkey Displays its own SSH public keys stored on

Strany 613 - IP Routing Commands 617

654 IPv6 Routing Commandswww.dell.com | support.dell.com

Strany 614

Loopback Interface Commands 655Loopback Interface Commandsinterface loopbackUse the interface loopback command in Global Configuration mode to enter t

Strany 615 - IP Routing Commands 619

656 Loopback Interface Commandswww.dell.com | support.dell.comSyntaxshow interfaces loopback [loopback-id]•loopback-id—Loopback identifier. (Range: 0-

Strany 616

Multicast Commands 659Multicast Commands ip mcast boundaryUse the ip mcast boundary command in Interface Configuration mode to add an administrative s

Strany 617 - IP Routing Commands 621

660 Multicast Commandswww.dell.com | support.dell.comip multicastUse the ip multicast command in Global Configuration mode to set the administrative m

Strany 618

Multicast Commands 661Syntaxip multicast staticroute sourceipaddr mask rpfipaddr metric vlan vlan-idno ip multicast staticroute sourceipaddr•sourceipa

Strany 619

662 Multicast Commandswww.dell.com | support.dell.comCommand ModeInterface Configuration (VLAN) modeUser GuidelinesThis command has no user guidelines

Strany 620

Multicast Commands 663mstatUse the mstat command in Privileged EXEC mode to find the IP Multicast packet rate and loss information path from a source

Strany 621

664 Multicast Commandswww.dell.com | support.dell.com•group/destination—Multicast IP address of the group being displayed/IP address of the receiver d

Strany 622

Multicast Commands 665ExampleThe following example clears entries in the mroute table. console(config)#no ip mcast mroute allshow ip mcastUse the show

Strany 623 - IP Routing Commands 627

28 Command Groupswww.dell.com | support.dell.comTACACS+ CommandsTelnet Server CommandsVLAN CommandsCommand Description Mode*key Specifies the authenti

Strany 624 - 628 IP Routing Commands

666 Multicast Commandswww.dell.com | support.dell.comSyntaxshow ip mcast boundary {vlan vlan-id | all}•vlan-id—Valid VLAN ID.Default ConfigurationThis

Strany 625 - IPv6 Routing Commands

Multicast Commands 667ExampleThe following example displays the multicast information for VLAN 15. console#show ip mcast interface vlan 15Interface TT

Strany 626

668 Multicast Commandswww.dell.com | support.dell.comshow ip mcast mrouteUse the show ip mcast mroute command in Privileged EXEC mode to display a sum

Strany 627 - IPv6 Routing Commands 631

Multicast Commands 669show ip mcast mroute groupUse the show ip mcast mroute group command in Privileged EXEC mode to display the multicast configurat

Strany 628

670 Multicast Commandswww.dell.com | support.dell.comshow ip mcast mroute sourceUse the show ip mcast mroute source command in Privileged EXEC mode to

Strany 629 - IPv6 Routing Commands 633

Multicast Commands 671show ip mcast mroute staticUse the show ip mcast mroute static command in Privileged EXEC mode to display all the static routes

Strany 630

672 Multicast Commandswww.dell.com | support.dell.comSyntaxshow mrinfoDefault ConfigurationThis command has no default configuration.Command ModePriv

Strany 631 - IPv6 Routing Commands 635

Multicast Commands 673ExampleThe following example displays the results of packet rate and loss information.console#show mstatResults for 'show m

Strany 632

674 Multicast Commandswww.dell.com | support.dell.com

Strany 633 - IPv6 Routing Commands 637

OSPF Commands 675OSPF Commandsarea default-costUse the area default-cost command in Router OSPF Configuration mode to configure the monetary default c

Strany 634

Command Groups 29name Configures a name to a VLAN. ICprotocol group Attaches a vlanid to the protocol-based VLAN identified by groupid.VLANprotocol v

Strany 635 - IPv6 Routing Commands 639

676 OSPF Commandswww.dell.com | support.dell.comarea nssaUse the area nssa command in Router OSPF Configuration mode to configure the specified area I

Strany 636

OSPF Commands 677•non-comparable—A metric type of nssa-external 2Default ConfigurationIf no metric is defined, 10 is the default configuration.Command

Strany 637 - IPv6 Routing Commands 641

678 OSPF Commandswww.dell.com | support.dell.comarea nssa no-summaryUse the area nssa no-summary command in Router OSPF Configuration mode to configur

Strany 638

OSPF Commands 679Command ModeRouter OSPF Configuration modeUser GuidelinesThis command has no user guidelines.ExampleThe following example configures

Strany 639 - FE80::202:BCFF:FE00:3068/128

680 OSPF Commandswww.dell.com | support.dell.comarea rangeUse the area range command in Router OSPF Configuration mode to configure a summary prefix f

Strany 640

OSPF Commands 681area stubUse the area stub command in Router OSPF Configuration mode to create a stub area for the specified area ID. A stub area is

Strany 641 - IPv6 Routing Commands 645

682 OSPF Commandswww.dell.com | support.dell.comDefault ConfigurationDisabled is the default configuration.Command ModeRouter OSPF Configuration modeU

Strany 642

OSPF Commands 683area virtual-link authenticationUse the area virtual-link authentication command in Router OSPF Configuration mode to configure the a

Strany 643 - IPv6 Routing Commands 647

684 OSPF Commandswww.dell.com | support.dell.comarea area-id virtual-link neighbor-id dead-interval secondsno area area-id virtual-link neighbor-id de

Strany 644

OSPF Commands 685Default Configuration10 seconds is the default configuration.Command ModeRouter OSPF Configuration modeUser GuidelinesThis command ha

Strany 645

30 Command Groupswww.dell.com | support.dell.comWeb Server Commandsvlan Creates a VLAN. VLANvlan association mac Associates a MAC address to a VLAN. V

Strany 646

686 OSPF Commandswww.dell.com | support.dell.comconsole(config-router)#area 10 virtual-link 192.168.2.2 retransmit-interval 500area virtual-link trans

Strany 647

OSPF Commands 687•always—Always advertise default routes.•integer—The metric (or preference) value of the default route. (Range: 1-16777214)•1—Externa

Strany 648

688 OSPF Commandswww.dell.com | support.dell.comExampleThe following example sets a value of 50 for the default metric.console(config-router)#default-

Strany 649

OSPF Commands 689no distribute-list accesslistname out {rip|static \ connected} •accesslistname—The name used to identify an existing ACL. The range

Strany 650 - 654 IPv6 Routing Commands

690 OSPF Commandswww.dell.com | support.dell.comExampleThe following example enables OSPF router mode.console(config-router)#enableexit-overflow-inter

Strany 651 - Loopback Interface Commands

OSPF Commands 691no external-lsdb-limit•integer—Maximum number of non-default ASexternal-LSAs allowed in the router's link-state database. (Range

Strany 652

692 OSPF Commandswww.dell.com | support.dell.comip ospf areaidUse the ip ospf areaid command in Interface Configuration mode to set the OSPF area to w

Strany 653 - Multicast Commands

OSPF Commands 693•key-id—Authentication key identifier for the authentication type encrypt. (Range: 0-255)Default ConfigurationThis command has no def

Strany 654

694 OSPF Commandswww.dell.com | support.dell.comip ospf dead-intervalUse the ip ospf dead-interval command in Interface Configuration to set the OSPF

Strany 655 - Multicast Commands 661

OSPF Commands 695Command ModeInterface Configuration (VLAN) modeUser GuidelinesThe value for the length of time must be the same for all routers attac

Strany 656

Command Groups 31show crypto certificate mycertificateDisplays the SSL certificates of your switch. PEshow ip http Displays the HTTP server configurat

Strany 657 - Multicast Commands 663

696 OSPF Commandswww.dell.com | support.dell.comip ospf priorityUse the ip ospf priority command in Interface Configuration mode to set the OSPF prior

Strany 658

OSPF Commands 697Command ModeInterface Configuration (VLAN) modeUser GuidelinesA value of 1 is the highest router priority. A value of 0 indicates tha

Strany 659 - Multicast Commands 665

698 OSPF Commandswww.dell.com | support.dell.comip ospf transmit-delayUse the ip ospf transmit-delay command in Interface Configuration mode to set th

Strany 660

OSPF Commands 699User GuidelinesThis command has no user guidelines.ExampleThe following example sets the number of paths at 2 that OSPF can report fo

Strany 661 - ---------

700 OSPF Commandswww.dell.com | support.dell.comExampleThe following example configures OSPF protocol to allow redistribution of routes from the speci

Strany 662

OSPF Commands 701User GuidelinesThe command prompt changes when the router ospf command executes.ExampleThe following example enters into router OSPF

Strany 663

702 OSPF Commandswww.dell.com | support.dell.comExternal LSA Checksum... 0New LSAs Originated... 0LSAs

Strany 664

OSPF Commands 703Exampleconsole#show ip ospf abrType Router Id Cost Area ID Next Hop Next Hop

Strany 665

704 OSPF Commandswww.dell.com | support.dell.comArea LSA Checksum... 0Import Summary LSAs... Enabl

Strany 666

OSPF Commands 705User GuidelinesThis command has no user guidelines.Exampleconsole#show ip ospf asbrType Router Id Cost Area ID Next Hop Nex

Strany 667

Contents 5clear bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116port security. . . . . . . . . . . . . . . . . . . . . .

Strany 668 - 674 Multicast Commands

32 Command Groupswww.dell.com | support.dell.comLayer 3 CommandsARP CommandsDHCP and BOOTP Relay CommandsCommand Description Mode*arp Creates an Addre

Strany 669 - OSPF Commands

706 OSPF Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeUser Gu

Strany 670

OSPF Commands 707Network... 0Summary Net... 0Summary ASBR...

Strany 671 - OSPF Commands 677

708 OSPF Commandswww.dell.com | support.dell.comTotal... 0show ip ospf interfaceUse the show ip ospf interface

Strany 672

OSPF Commands 709Iftransit Delay Interval... 1Authentication Type... NoneMetric Cost...

Strany 673 - OSPF Commands 679

710 OSPF Commandswww.dell.com | support.dell.comloopback2 Disable 0.0.0.0 1 10 40 5 1 1show ip ospf interface statsUse the s

Strany 674

OSPF Commands 711Syntaxshow ip ospf neighbor [interface vlan vlan-id] [ip-address]•vlan-id—Valid VLAN ID.•ip-address—Valid IP address of the neighbor

Strany 675 - OSPF Commands 681

712 OSPF Commandswww.dell.com | support.dell.com•area-id—Identifies the OSPF area whose ranges are being displayed. (Range: IP address or decimal from

Strany 676

OSPF Commands 713Exampleconsole>show ip ospf statisticsArea 0.0.0.0: SPF algorithm executed 0 timesDelta T SPF Duration (msec) Reason-----

Strany 677 - OSPF Commands 683

714 OSPF Commandswww.dell.com | support.dell.comshow ip ospf virtual-linkUse the show ip ospf virtual-link command in Privileged EXEC mode to display

Strany 678

OSPF Commands 715show ip ospf virtual-link briefUse the show ip ospf virtual-link brief command in Privileged EXEC mode to display the OSPF Virtual In

Strany 679 - OSPF Commands 685

Command Groups 33DHCPv6 Commandsshow bootpdhcprelay Displays the BootP/DHCP Relay information. UE *NOTE: For the meaning of each Mode abbreviation, s

Strany 680

716 OSPF Commandswww.dell.com | support.dell.comCommand ModeRouter OSPF Configuration modeUser GuidelinesThis command has no user guidelines.ExampleTh

Strany 681 - OSPF Commands 687

OSPF Commands 717Default ConfigurationEnabled is the default configuration.Command ModeRouter OSPF Configuration modeUser GuidelinesIf all OSPF router

Strany 682

718 OSPF Commandswww.dell.com | support.dell.com

Strany 683 - OSPF Commands 689

OSPFv3 Commands 719OSPFv3 Commands area default-costUse the area default-cost command in Router OSPFv3 Configuration mode to configure the monetary de

Strany 684

720 OSPFv3 Commandswww.dell.com | support.dell.comSyntaxarea areaid nssano area areaid nssa•areaid—Valid OSPFv3 area identifier.Default ConfigurationT

Strany 685 - OSPF Commands 691

OSPFv3 Commands 721Command ModeRouter OSPFv3 Configuration modeUser GuidelinesThis command has no user guidelines.ExampleThe following example configu

Strany 686

722 OSPFv3 Commandswww.dell.com | support.dell.comarea nssa no-summaryUse the area nssa no-summary command in Router OSPFv3 Configuration mode to conf

Strany 687 - OSPF Commands 693

OSPFv3 Commands 723Default ConfigurationThis command has no default configuration.Command ModeRouter OSPFv3 Configuration modeUser GuidelinesThis comm

Strany 688

724 OSPFv3 Commandswww.dell.com | support.dell.comconsole(config-rtr)#area 1 nssa translator-stab-intv 100area rangeUse the area range command in Rout

Strany 689 - OSPF Commands 695

OSPFv3 Commands 725area stubUse the area stub command in Router OSPFv3 Configuration mode to create a stub area for the specified area ID. A stub area

Strany 690

34 Command Groupswww.dell.com | support.dell.comDVMRP CommandsIGMP CommandsCommand Description Mode*ip dvmrp Sets the administrative mode of DVMRP in

Strany 691

726 OSPFv3 Commandswww.dell.com | support.dell.comCommand ModeRouter OSPFv3 Configuration modeUser GuidelinesThis command has no user guidelines.Examp

Strany 692

OSPFv3 Commands 727area virtual-link dead-intervalUse the area virtual-link dead-interval command in Router OSPFv3 Configuration mode to configure the

Strany 693 - OSPF Commands 699

728 OSPFv3 Commandswww.dell.com | support.dell.com•seconds—Hello interval. (Range: 1-65535)Default Configuration10 is the default value for seconds. C

Strany 694

OSPFv3 Commands 729ExampleThe following example configures the retransmit interval of 20 seconds for the OSPF virtual interface on the virtual interfa

Strany 695 - OSPF Commands 701

730 OSPFv3 Commandswww.dell.com | support.dell.comSyntaxdefault-information originate [always] [metric integer] [metric-type {1 | 2}]no default-inform

Strany 696

OSPFv3 Commands 731Command ModeRouter OSPFv3 Configuration modeUser GuidelinesThis command has no user guidelines.ExampleThe following example sets a

Strany 697 - OSPF Commands 703

732 OSPFv3 Commandswww.dell.com | support.dell.comenableUse the enable command in Router OSPFv3 Configuration mode to enable administrative mode of OS

Strany 698

OSPFv3 Commands 733Command ModeRouter OSPFv3 Configuration modeUser GuidelinesThis command has no user guidelines.ExampleThe following example configu

Strany 699

734 OSPFv3 Commandswww.dell.com | support.dell.comipv6 ospfUse the ipv6 ospf command in Interface Configuration mode to enable OSPF on a router interf

Strany 700

OSPFv3 Commands 735Command ModeInterface Configuration (VLAN, Tunnel, Loopback) modeUser GuidelinesThis command has no user guidelines.ExampleThe foll

Strany 701 - OSPF Commands 707

Command Groups 35IGMP Proxy Commandsip igmp startup-query-count Sets the number of queries sent out on startup - at intervals equal to the startup que

Strany 702

736 OSPFv3 Commandswww.dell.com | support.dell.comSyntaxipv6 ospf dead-interval secondsno ipv6 ospf dead-interval•seconds—A valid positive integer, wh

Strany 703

OSPFv3 Commands 737User GuidelinesThis command has no user guidelines.ExampleThe following example sets the OSPF hello interval at 15 seconds.console(

Strany 704

738 OSPFv3 Commandswww.dell.com | support.dell.comipv6 ospf networkUse the ipv6 ospf network command in Interface Configuration mode to change the def

Strany 705 - OSPF Commands 711

OSPFv3 Commands 739Default Configuration1, the highest router priority, is the default value.Command ModeInterface Configuration (VLAN, Tunnel, Loopba

Strany 706

740 OSPFv3 Commandswww.dell.com | support.dell.comipv6 ospf transmit-delayUse the ipv6 ospf transmit-delay command in Interface Configuration mode to

Strany 707 - OSPF Commands 713

OSPFv3 Commands 741User GuidelinesThis command has no user guidelines.ExampleUse the following command to enable OSPFv3.console(config)#ipv6 router os

Strany 708

742 OSPFv3 Commandswww.dell.com | support.dell.comSyntaxredistribute {static | connected} [metric metric] [metric-type {1 | 2}] [tag tag ]no redistrib

Strany 709 - OSPF Commands 715

OSPFv3 Commands 743ExampleThe following example sets a 4-digit dotted-decimal number identifying the Router OSPF ID as 2.3.4.5. console(config)#ipv6 r

Strany 710 - 1583compatibility

744 OSPFv3 Commandswww.dell.com | support.dell.comDefault Metric... Not ConfiguredMaximum Paths...

Strany 711

OSPFv3 Commands 745Syntaxshow ipv6 ospf area areaid •areaid—Identifier for the OSPF area being displayed. Default ConfigurationThis command has no def

Strany 712 - 718 OSPF Commands

36 Command Groupswww.dell.com | support.dell.comIP Routing CommandsIPv6 Routing CommandsCommand Description Mode*encapsulation Configures the link la

Strany 713 - OSPFv3 Commands

746 OSPFv3 Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.Exampleconsole#sh

Strany 714

OSPFv3 Commands 747• unknown—Displays unknown area, AS or link-scope LSAs.•lsid—Specifies a valid link state identifier (LSID).• adv-router—Shows the

Strany 715 - OSPFv3 Commands 721

748 OSPFv3 Commandswww.dell.com | support.dell.comExampleThe following example displays information about the link state database when OSPFv3 is enabl

Strany 716

OSPFv3 Commands 749 Link States (Area 0.0.0.0)Adv Router Link Id Age Sequence Csum Options Rtr Opt-------------- -------

Strany 717 - OSPFv3 Commands 723

750 OSPFv3 Commandswww.dell.com | support.dell.com Link States (Area 0.0.0.1)Adv Router Link Id Age Sequence Csum Option

Strany 718

OSPFv3 Commands 751Router database summaryRouter... 0Network... 0Inter-area

Strany 719 - OSPFv3 Commands 725

752 OSPFv3 Commandswww.dell.com | support.dell.comExampleThe following example displays the information in VLAN 11’s virtual interface tables. console

Strany 720

OSPFv3 Commands 753ExampleThe following example displays brief ospf interface information. console#show ipv6 ospf interface brief

Strany 721 - OSPFv3 Commands 727

754 OSPFv3 Commandswww.dell.com | support.dell.comVirtual Events... 13Neighbor Events... 6E

Strany 722

OSPFv3 Commands 755Command ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines. ExampleThe following example displays ospf inte

Strany 723 - OSPFv3 Commands 729

Command Groups 37ipv6 enable Enables IPv6 routing on an interface (including tunnel and loopback interfaces) that has not been configured with an expl

Strany 724

756 OSPFv3 Commandswww.dell.com | support.dell.comshow ipv6 ospf neighborUse the show ipv6 ospf neighbor command in Privileged EXEC mode to display in

Strany 725 - OSPFv3 Commands 731

OSPFv3 Commands 757Retransmit Interval... 5Hello Interval... 10Dead Interval...

Strany 726

758 OSPFv3 Commandswww.dell.com | support.dell.comSyntaxshow ipv6 ospf stub table Default ConfigurationThis command has no default configuration. Comm

Strany 727 - OSPFv3 Commands 733

OSPFv3 Commands 759ExampleThe following example displays the OSPF Virtual Interface information for area 1 and its neighbor. console#show ipv6 ospf vi

Strany 728

760 OSPFv3 Commandswww.dell.com | support.dell.comtrapflagsUse the trapflags command in Router OSPFv3 Configuration mode to enable OSPF traps.Syntaxtr

Strany 729 - OSPFv3 Commands 735

PIM-DM Commands 763PIM-DM Commands ip pimdmUse the ip pimdm command in Global Configuration mode to enable the administrative mode of PIM-DM in the ro

Strany 730

764 PIM-DM Commandswww.dell.com | support.dell.comSyntaxip pimdm modeno ip pimdm mode Default ConfigurationDisabled is the default state.Command ModeI

Strany 731 - OSPFv3 Commands 737

PIM-DM Commands 765console(config)#interface vlan 15console(config-if-vlan15)#ip pimdm query-interval 50show ip pimdmUse the show ip pimdm command in

Strany 732

766 PIM-DM Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user guidelines.ExampleThe follow

Strany 733 - OSPFv3 Commands 739

PIM-DM Commands 767show ip pimdm neighborUse the show ip pimdm neighbor command in Privileged EXEC mode to display the neighbor information for PIM-DM

Strany 734

38 Command Groupswww.dell.com | support.dell.comLoopback Interface CommandsMulticast Commandsshow ipv6 route preference Shows the preference value ass

Strany 735 - OSPFv3 Commands 741

768 PIM-DM Commandswww.dell.com | support.dell.com

Strany 736

PIM-SM Commands 769PIM-SM Commands ip pimsmUse the ip pimsm command in Global Configuration mode to set administrative mode of PIM-SM multicast routin

Strany 737 - OSPFv3 Commands 743

770 PIM-SM Commandswww.dell.com | support.dell.comSyntaxip pimsm cbsrhashmasklength masklengthno ip pimsm cbsrhashmasklength•masklength—CBSR hash mask

Strany 738

PIM-SM Commands 771ExampleThe following example configures the CBSR preference of 5 for VLAN 15.console(config)#interface vlan 15console(config-if-vla

Strany 739 - OSPFv3 Commands 745

772 PIM-SM Commandswww.dell.com | support.dell.com Syntaxip pimsm message-interval intervalno ip pimsm message-interval•interval—Join/prune interval.

Strany 740

PIM-SM Commands 773console(config-if-vlan15)#ip pimsm modeip pimsm query-intervalUse the ip pimsm query-interval command in Interface Configuration mo

Strany 741

774 PIM-SM Commandswww.dell.com | support.dell.comCommand ModeGlobal Configuration (VLAN) modeUser GuidelinesUse this command to control the number of

Strany 742

PIM-SM Commands 775 Syntaxip pimsm staticrp ipaddr groupaddr groupmask no ip pimsm staticrp ipaddr groupaddr groupmask •ipaddr—IP address of RP.•grou

Strany 743 - OSPFv3 Commands 749

776 PIM-SM Commandswww.dell.com | support.dell.comExampleThe following example enables PIM trap mode.console(config)#ip pim-trapflagsshow ip pimsmUse

Strany 744

PIM-SM Commands 777 Syntaxshow ip pimsm componenttableDefault ConfigurationThis command has no default configuration.Command ModePrivileged EXEC modeU

Strany 745

Command Groups 39OSPF Commandsshow ip mcast interface Displays the multicast information for the specified interface.PEshow ip mcast mroute Displays

Strany 746

778 PIM-SM Commandswww.dell.com | support.dell.comExampleThe following example displays interface information for VLAN 11 PIM-SM.console#show ip pimsm

Strany 747

PIM-SM Commands 779show ip pimsm neighborUse the show ip pimsm neighbor command in Privileged EXEC mode to display neighbor information for PIM-SM on

Strany 748

780 PIM-SM Commandswww.dell.com | support.dell.com• candidate — Display PIM-SM candidate-RP table information.Default ConfigurationThis command has no

Strany 749

PIM-SM Commands 781ExampleThe following example displays the RP router being selected from the set of active RP routers.console#show ip pimsm rphash 2

Strany 750

782 PIM-SM Commandswww.dell.com | support.dell.com

Strany 751

Router Discovery Protocol Commands 783Router Discovery Protocol Commandsip irdpUse the ip irdp command in Interface Configuration mode to enable Route

Strany 752

784 Router Discovery Protocol Commandswww.dell.com | support.dell.comSyntaxip irdp address ip-address no ip irdp address •ip-address—IP address for ro

Strany 753 - OSPFv3 Commands 759

Router Discovery Protocol Commands 785User GuidelinesThis command has no user guidelines.ExampleThe following example sets hold time at 2000 seconds f

Strany 754

786 Router Discovery Protocol Commandswww.dell.com | support.dell.comSyntaxip irdp minadvertinterval integerno ip irdp minadvertinterval •integer—Mini

Strany 755 - PIM-DM Commands

Router Discovery Protocol Commands 787User GuidelinesThis command has no user guidelines.ExampleThe following example sets the ip irdp preference to 1

Strany 756

40 Command Groupswww.dell.com | support.dell.comarea virtual-link Creates the OSPF virtual interface for the specified area-id and neighbor router.ROS

Strany 757 - PIM-DM Commands 765

788 Router Discovery Protocol Commandswww.dell.com | support.dell.com

Strany 758

Routing Information Protocol (RIP) Commands 789Routing Information Protocol (RIP) Commandsauto-summaryUse the auto-summary command in Router RIP Confi

Strany 759

790 Routing Information Protocol (RIP) Commandswww.dell.com | support.dell.comDefault ConfigurationThis command has no default configuration.Command M

Strany 760 - 768 PIM-DM Commands

Routing Information Protocol (RIP) Commands 791Syntaxdistance rip integerno distance rip•integer—RIP route preference. (Range: 1-255)Default Configura

Strany 761 - PIM-SM Commands

792 Routing Information Protocol (RIP) Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following

Strany 762

Routing Information Protocol (RIP) Commands 793Default ConfigurationEnabled is the default configuration.Command ModeRouter RIP Configuration mode.Use

Strany 763 - PIM-SM Commands 771

794 Routing Information Protocol (RIP) Commandswww.dell.com | support.dell.comno ip rip authentication•key—Authentication key for the specified interf

Strany 764

Routing Information Protocol (RIP) Commands 795User GuidelinesThis command has no user guidelines.ExampleThe following example allows no RIP control p

Strany 765 - PIM-SM Commands 773

796 Routing Information Protocol (RIP) Commandswww.dell.com | support.dell.comredistribute ospf [metric integer] [match [internal] [external 1] [exter

Strany 766

Routing Information Protocol (RIP) Commands 797Default ConfigurationThis command has no default configuration.Command ModeGlobal Configuration modeUse

Strany 767 - PIM-SM Commands 775

Command Groups 41ip ospf retransmit-interval Sets the OSPF retransmit Interval for the specified interface.ICip ospf transmit-delay Sets the OSPF Tran

Strany 768

798 Routing Information Protocol (RIP) Commandswww.dell.com | support.dell.comGlobal route changes... 0Global queries...

Strany 769 - PIM-SM Commands 777

Routing Information Protocol (RIP) Commands 799Interface... 15IP Address... -----

Strany 770

800 Routing Information Protocol (RIP) Commandswww.dell.com | support.dell.com---------- ---------- -------- ----------- --------- ----------vlan1

Strany 771 - PIM-SM Commands 779

Tunnel Interface Commands 803Tunnel Interface Commandsinterface tunnelUse the interface tunnel command in Global Configuration mode to enter the inter

Strany 772

804 Tunnel Interface Commandswww.dell.com | support.dell.comSyntaxshow interfaces tunnel [tunnel-id ]•tunnel-id—Tunnel identifier. (Range: 0-7)Default

Strany 773 - PIM-SM Commands 781

Tunnel Interface Commands 805Default ConfigurationThis command has no default configuration.Command ModeInterface Configuration (Tunnel) modeUser Guid

Strany 774 - 782 PIM-SM Commands

806 Tunnel Interface Commandswww.dell.com | support.dell.comtunnel sourceUse the tunnel source command in Interface Configuration mode to specify the

Strany 775

Virtual LAN Routing Commands 809Virtual LAN Routing Commandsshow ip vlanUse the show ip vlan command in Privileged EXEC mode to display the VLAN routi

Strany 776

810 Virtual LAN Routing Commandswww.dell.com | support.dell.comvlan routingUse the vlan routing command in VLAN Database mode to create routing on a V

Strany 777

Virtual Router Redundancy Protocol Commands 813Virtual Router Redundancy Protocol Commandsip vrrpUse the ip vrrp command in Global Configuration mode

Strany 778

6 Contentsshow clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1369 Denial of Service Commandsdos-control firstfrag . . . .

Strany 779

42 Command Groupswww.dell.com | support.dell.comOSPFv3 Commandstrapflags Enables OSPF traps. ROSPF1583compatibility Enables OSPF 1583 compatibility. R

Strany 780

814 Virtual Router Redundancy Protocol Commandswww.dell.com | support.dell.comThe following example in Interface Configuration mode enables VRRP proto

Strany 781 - Commands

Virtual Router Redundancy Protocol Commands 815ip vrrp vr-id ip ip-address [secondary]no ip vrrp vr-id ip ip-address secondary•vr-id—The virtual route

Strany 782

816 Virtual Router Redundancy Protocol Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following

Strany 783

Virtual Router Redundancy Protocol Commands 817Syntaxip vrrp vr-id priority priorityno ip vrrp vr-id priority •vr-id—The virtual router identifier. (

Strany 784

818 Virtual Router Redundancy Protocol Commandswww.dell.com | support.dell.comUser GuidelinesThis command has no user guidelines.ExampleThe following

Strany 785

Virtual Router Redundancy Protocol Commands 819show ip vrrp interface vlan vlan-id vr-id•vlan-id—Valid VLAN ID.•vr-id—The virtual router identifier.

Strany 786

820 Virtual Router Redundancy Protocol Commandswww.dell.com | support.dell.comCommand ModePrivileged EXEC modeUser GuidelinesThis command has no user

Strany 787

Virtual Router Redundancy Protocol Commands 821Protocol... IPState Transitioned to Master... 0Adve

Strany 788

822 Virtual Router Redundancy Protocol Commandswww.dell.com | support.dell.com

Strany 789

Command Groups 43default-metric Sets a default for the metric of distributed routes. ROSV3distance ospf Sets the route preference value of OSPF in the

Strany 790

44 Command Groupswww.dell.com | support.dell.comPIM-DM Commandsshow ipv6 ospf database database-summaryDisplays the number of each type of LSA in the

Strany 791

Command Groups 45PIM-SM Commands*NOTE: For the meaning of each Mode abbreviation, see Mode Types on page 4.Command Description Mode*ip pimsm Sets a

Strany 792

46 Command Groupswww.dell.com | support.dell.comRouter Discovery Protocol CommandsRouting Information Protocol (RIP) Commandsshow ip pimsm rp Displays

Strany 793 - Tunnel Interface Commands

Command Groups 47Tunnel Interface Commandsdistribute-list out Specifies the access list to filter routes received from the source protocol.RIPenable R

Strany 794

48 Command Groupswww.dell.com | support.dell.comVirtual LAN Routing CommandsVirtual Router Redundancy CommandsCommand Description Mode*show ip vlan

Strany 795 - Tunnel Interface Commands 805

Using the CLI 49Using the CLIThis chapter describes the basics of entering and editing the Dell PowerConnect 62xx Series Command Line Interface (CLI)

Strany 796

50 Using the CLIwww.dell.com | support.dell.com• Command Scripting• CLI Command Notation Conventions• Interface Naming ConventionsHistory BufferEvery

Strany 797 - Virtual LAN Routing Commands

Using the CLI 51Short Form CommandsThe CLI supports the short forms of all commands. As long as it is possible to recognize the entered command unambi

Strany 798

Contents 7show interfaces configuration. . . . . . . . . . . . . . . . . . . . . . . . 156show interfaces counters. . . . . . . . . . . . . . . . .

Strany 799

52 Using the CLIwww.dell.com | support.dell.comOperating on Multiple Objects (Range)The CLI allows the user to operate on the set of objects at the sa

Strany 800

Using the CLI 53CLI Command Notation ConventionsWhen entering commands there are certain command-entry notations which apply to all commands. The foll

Strany 801

54 Using the CLIwww.dell.com | support.dell.comIn this guide, commands are organized in two separate categories: Data Link Layer commands and Network

Strany 802

Using the CLI 55Privileged EXEC ModeBecause many of the privileged commands set operating parameters, privileged access is password-protected to preve

Strany 803

56 Using the CLIwww.dell.com | support.dell.com•Policy-map—Use the policy-map command to access the QoS policy map configuration mode to configure the

Strany 804

Using the CLI 57•Crypto Certificate Request— Configures the parameters for crypto certificate request.•Crypto Certificate Generation—Configures the pa

Strany 805

58 Using the CLIwww.dell.com | support.dell.comNavigating CLI Command ModesThe following table describes how to navigate through the CLI Command Mode

Strany 806

Using the CLI 59Class-Map From Global Configuration mode, use the class-map command.console(config-classmap)#To exit to Global Configuration mode, use

Strany 807

60 Using the CLIwww.dell.com | support.dell.comRadius From Global Configuration mode, use the radius-server host command.console(config-radius)#To exi

Strany 808

Using the CLI 61Stack From Global Configuration mode, use the stack command.console(config-stack)#To exit to Global Configuration mode, use the exit c

Komentáře k této Příručce

Žádné komentáře