Dell DAE2P Průvodce nastavením

Procházejte online nebo si stáhněte Průvodce nastavením pro Servery Dell DAE2P. Dell DAE2P Setup guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 27
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
EMC Corporation
Corporate Headquarters
:
Hopkinton, MA 01748
-9103
1
-508-435-1000
www.EMC.com
CX300
2-Gigabit Fibre Channel
Disk Processor Enclosure (DPE2)
SETUP GUIDE
P/N 300-001-276
REV A05
Zobrazit stránku 0
1 2 3 4 5 6 ... 26 27

Shrnutí obsahu

Strany 1 - SETUP GUIDE

EMC CorporationCorporate Headquarters:Hopkinton, MA 01748-91031-508-435-1000www.EMC.comCX3002-Gigabit Fibre ChannelDisk Processor Enclosure (DPE2)SET

Strany 2 - Trademark Information

8 Step 6Verify Storage System Back-End ConnectionsUse the information below and the diagram to verify the enclosure address settings and loop (bus) c

Strany 3 - Overview

9 Step 7Verify Power Settings and Connections1. Verify that the cabinet master switches are in the off position.2. For systems that use ac power, veri

Strany 4 - Plan Your Configuration

10 Step 7 ContinuedVerify Power Settings and Connections• In systems with dc power, connect DB9-RJ12 sense cables (sometimes called SPS emulator cabl

Strany 5 - Prepare Your Environment

11 Step 8Start the Storage System1. Turn on the power switches for the DPE2 and any DAE power/cooling modules (if present).2. Turn on the power switch

Strany 6 - Verify the Parts

12 Step 9Connect the Storage System Management PortsUsing CAT 5 or better Ethernet cables, connect each SP to the same subnet that is connected to the

Strany 7 - Registered

13 Step 10Initialize the Storage System To initialize the storage system, you must configure the management network interfaces for the storage system’

Strany 8 - Step 4 Continued

14 Step 10 ContinuedInitialize the Storage System ❒ The completed configuration planning worksheets from the EMC CLARiiON CX300, CX300i, CX500, CX500i

Strany 9

15 Step 10 ContinuedInitialize the Storage System Install the Navisphere Storage System Initialization UtilityInstall the Storage System Initializatio

Strany 10 - EMC3223

16 Step 10 ContinuedInitialize the Storage System2. Start the initialization utility:• HP-UX hostOpen an hpterm window and enter/opt/Navisphere/bin/na

Strany 11

17 Step 10 ContinuedInitialize the Storage System4. Select the storage system to initialize:• On an HP-UX, Linux, NetWare, or Solaris hostEnter the it

Strany 12 - Step 7 Continued

NoticeCopyright © 2004-2005 EMC Corporation. All rights reserved.Printed August, 2005EMC believes the information in this publication is accurate as o

Strany 13 - Start the Storage System

18 Step 11Connect the Storage-System Data PortsYou use fiber-optic cables to connect the storage-system data ports to the server’s Fibre Channel HBAs

Strany 14

19 Step 11 ContinuedConnect the Storage-System Data PortsWhat Next?If you installed the Host Agent on the server, continue to Step 12, Run the Host Ag

Strany 15 - Step 10

20 Step 12Run the Host Agent to Register the Server HBAsWhen the Host Agent starts, it registers server HBAs with any storage systems that are connect

Strany 16 - Step 10 Continued

21 Step 12 ContinuedRun the Host Agent to Register the Server HBAs• NetWare serverTo start the Host Agent:load sys:\emc\agent\navagent -f sys:\emc\

Strany 17

22 Step 13Run the Server Utility to Register the Server HBAs1. Start the server utility:• AIX server/usr/lpp/HOSTUTIL/naviserverutil• HP-UX serverOpen

Strany 18

23 Step 14Enable SoftwareThe following software is enabled on the storage system prior to shipment from the factory:• Navisphere Manager• Access Logix

Strany 19

24 Step 15Configure the Storage SystemYou are now ready to use Navisphere Manager to define your storage-system security settings and configure your s

Strany 20 - Step 11

25If You Need HelpFor questions about technical support and service, contact your service provider. If you have an EMC service contract, contact EMC C

Strany 21 - Step 11 Continued

1OverviewThis guide explains how to install and initialize an EMC® CLARiiON® CX300 2-gigabit disk processor enclosure (DPE2). Only an authorized servi

Strany 22 - Step 12

2 Step 1Plan Your ConfigurationTo plan your installation, refer to the EMC CLARiiON CX300, CX300i, CX500, CX500i, and CX700 Storage Systems Configurat

Strany 23 - Step 12 Continued

3 Step 2Prepare Your Environment1. Verify that your facility has adequate network wiring to provide eachstorage-system storage processor (SP) with a m

Strany 24 - Step 13

4 Step 3Verify the PartsVerify that your basic configuration has the following parts:❒ CX300 DPE2with:❒ Two storage processors (SPs)❒ Two power supply

Strany 25 - Step 14

5 Step 4Install the Host Agent or Server UtilityYou can use either the Navisphere® Host Agent or the Navisphere Server Utility to register the server

Strany 26 - Step 15

6 Step 4 ContinuedInstall the Host Agent or Server UtilityIf you have not already installed the Host Agent or the Server Utility, install it now. Foll

Strany 27 - If You Need Help

7 Step 5Install the Storage System in the CabinetIf your CX300 DPE2 enclosure or any DAEs are not already installed in a cabinet, install them using t

Komentáře k této Příručce

Žádné komentáře