Dell Force10 S55T Příručka pro rychlý start Strana 1

Procházejte online nebo si stáhněte Příručka pro rychlý start pro Servery Dell Force10 S55T. Dell Force10 S55T Quick Start Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Quick Start Guide

Dell Force10S55 and S60 SystemsQuick Start GuideRegulatory Model: S55/S60

Strany 2

8 Installing the Hardware NOTE: Coat the one-hole lug with an anti-oxidant compound prior to crimping. Bring any un-plated mating surfaces to a shiny

Strany 3

Installing the Hardware 9Install the SFP and SFP+ OpticsThe chassis are shipped as follows:• The S55 has 4 SFP optical ports in the PSU side of the ch

Strany 4 - Notes, Cautions, and Warnings

10 Installing the Hardware• The input circuits are correctly sized for the loads and that sufficient over-current protection devices are used.• All pr

Strany 5 - About this Guide

Installing the Hardware 11Power SuppliesThe S55 and S60 chassis are designed to support two hot-swappable power supplies with integrated fans that pro

Strany 6 - 4 About this Guide

12 Installing the Hardware NOTE: Both slots must have operating fan units to run the system. If a module is not installed in each slot (either as par

Strany 7 - Installing the Hardware

Installing the Hardware 13Environmental ParametersAC Power RequirementsDC Power RequirementsPower SuppliesThe S55 and the S60 are designed to support

Strany 8 - 6 Installing the Hardware

14 Installing the Hardware WARNING: To prevent electrical shock, make sure the systems are grounded properly. If you do not ground your equipment cor

Strany 9

Installing the Hardware 15Install a DC Power SupplyThe power supply modules should slide into the slots smoothly. Do not force a module into a slot. T

Strany 10 - 8 Installing the Hardware

16 Installing the Hardware

Strany 11 - Power Up Sequence

Installing the Software 172Installing the SoftwareNavigating CLI ModesThe FTOS prompt changes to indicate the CLI mode. You must move linearly through

Strany 13 - Power Supplies

18 Installing the SoftwareSerial ConsoleThe RS-232 console port is labeled on the chassis. It is in the upper right-hand side, as you face the rear of

Strany 14 - Specifications

Installing the Software 19USB-B ConsoleThe USB-B connector port is labeled on the S55/S60 chassis. It is to the left of the management ports, as you f

Strany 15

20 Installing the SoftwareDefault ConfigurationA version of the Dell Force10 Operating System (FTOS) is pre-loaded onto the chassis, however the syste

Strany 16

Installing the Software 21Access the System RemotelyYou can configure the system to be accessed remotely by Telnet. Both the S55 and the S60 has a ded

Strany 17 - Install a DC Power Supply

22 Installing the SoftwareConfigure a Username and PasswordConfigure a system username and password to access the system remotely.Configure the Enable

Strany 18 - 16 Installing the Hardware

Installing the Software 23Create a Port-based VLANThe Default VLAN as VLAN 1 is part of the system startup configuration and does not require configur

Strany 19 - Installing the Software

24 Installing the SoftwareUse the untagged command to move untagged interfaces from the Default VLAN to another VLAN:Assign an IP address to a VLAN N

Strany 21 - USB-B Console

www.dell.com | support.dell.comPrinted in the U.S.A.

Strany 22 - Configure a Host Name

Dell Force10S55 and S60 SystemsQuick Start GuideRegulatory Model: S55/S60

Strany 23 - Access the System Remotely

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indic

Strany 24 - Configure the Enable Password

About this Guide 3About this GuideThis document is intended as a Quick Start Guide to get new systems up and running and ready for configuration. For

Strany 26 - 2 Configure an interface

Installing the Hardware 51Installing the HardwareThis guide assumes all site preparation has been performed before installing the chassis.Installing t

Strany 27

6 Installing the Hardware2 Attach the brackets to the sides of the chassis at the PSU end, using four screws for each bracket. Attach the bracket so t

Strany 28 - Printed in the U.S.A

Installing the Hardware 7Install Chassis into Rack or CabinetEnsure that there is adequate clearance surrounding the rack or within the cabinet to per

Komentáře k této Příručce

Žádné komentáře