Dell SC PERC 3 Uživatelská příručka

www.dell.com | support.dell.comDell™ PowerEdge™ DiagnosticsVersion 2.7User’s Guide

10 Setting Up DiagnosticsSetup and Diagnostic RequirementsThe PowerEdge Diagnostics must be set up on each managed system to run diagnostics locally.

Setting Up Diagnostics 11 NOTE: Memory diagnostics are not supported on the following PowerEdge systems as they do not support IPMI: SC420, SC430, SC

12 Setting Up DiagnosticsSetting Up DiagnosticsThe files required to run PowerEdge Diagnostics for Microsoft Windows and Linux operating systems are a

Setting Up Diagnostics 13Installing PowerEdge Diagnostics on LinuxThe following steps show how to install PowerEdge Diagnostics on systems running sup

14 Setting Up Diagnostics

Using Diagnostics 15Using Dell PowerEdge DiagnosticsDell™ PowerEdge™ Diagnostics can be accessed in two ways: from an integrated graphical user interf

16 Using Diagnostics•Save Results: Use this option to save the test result details. The test result details are saved to an HTML file (results.html),

Using Diagnostics 17Selection OptionsUse this list box to organize how tests and detected devices are displayed. You can select any of the three optio

18 Using DiagnosticsDiagnostic InformationUse this section to view the system configuration and operational status information. In addition, you can r

Using Diagnostics 19Diagnostic Options: Use this section of the Tests Selected tab to run the selected tests. This section contains the following cont

Notes and Notices NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either pot

20 Using DiagnosticsResult: Specifies the result of a test in the form of symbols. For example, the Status column of a test might show as Completed, b

Using Diagnostics 21The Command Line InterfaceTo run the application in CLI mode, run pediags from <ExtractDir>/oldiags/bin, which should be the

22 Using Diagnostics•pediags <DEVICECLASS> --run [<Index Options>] [<Test Settings>] [fmt=lst|tbl|xml]This command runs tests on the

Using Diagnostics 23You can also use the exit codes explained in the following table when writing scripts.Exit codes 0, 1, and 2 are applicable for on

24 Using Diagnostics

Running Diagnostics 25Running Dell PowerEdge Diagnostics in GUI ModeThis section provides step-by-step instructions on running Dell™ PowerEdge™ Diagno

26 Running Diagnostics4Click the Status tab to monitor the status of the test execution. • To abort a running test, right-click the test and select Ab

Running Diagnostics 273Select the Quick Test check box in the Diagnostic Options section at the bottom. If this option is available for one of the sel

28 Running Diagnostics NOTE: The Dell Remote Access Controller (DRAC) diagnostics tests require the RAC software components to be present on your sys

Supported Devices 29Supported DevicesThis section lists the devices that can be tested using Dell™ PowerEdge™ Diagnostics. Diagnostics for Tape Drives

Contents 3Contents1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Supported Operating Systems . . . . . . . . . .

30 Supported Devices• PowerVault 122T Autoloader LTO-2• PowerVault 132T Autoloader SDLT 320• PowerVault 132T Autoloader LTO-2 • PowerVault 136T Autolo

Supported Devices 31• PERC 3/QC•PERC 3/SC• PERC 3/Di• PERC 320/DC•PERC 4/SC• PERC 4/DC• PERC 4e/DC• PERC 4/Di• PERC 4e/Di•PERC 4e/Si•PERC 4/IM•PERC 5/

32 Supported Devices

Diagnostic Dependencies for Supported RAID Controllers 33Diagnostic Dependencies for Supported RAID ControllersOverviewDell™ PowerEdge™ Diagnostics re

34 Diagnostic Dependencies for Supported RAID ControllersPERC 3/SC, 3/DC and 3/QCTable 6-2 shows the elements supported by the PERC 3/DC and 3/QC cont

Diagnostic Dependencies for Supported RAID Controllers 35PERC 4/DC Table 6-5 shows the elements supported by the PERC 4/DC controller.PERC 4e/DiTable

36 Diagnostic Dependencies for Supported RAID ControllersPERC 4e/SiTable 6-8 shows the elements supported by the PERC 4e/Si controller.PERC 4/IMTable

Diagnostic Dependencies for Supported RAID Controllers 37PERC 5/E, PERC 5/i Integrated, and PERC 5/i AdapterTable 6-11 shows the elements supported by

38 Diagnostic Dependencies for Supported RAID ControllersCERC SATA 1.5/2STable 6-14 shows the elements supported by the CERC SATA 1.5/2S Channel contr

Diagnostic Dependencies for Supported RAID Controllers 39Appendix ATable A-1. Additional Hardware Information for Storage DiagnosticsParameter Descrip

4 ContentsConfiguring the Test Execution Settings . . . . . . . . . . . . . . . . . . 265 Supported Devices . . . . . . . . . . . . . . . . . . . .

40 Appendix ATape Motion Hours/Cylinder on Hours (COH)This represents the amount of time the tape drive has been used for backups and restores.Load Co

Introduction 5IntroductionDell™ PowerEdge™ Diagnostics is a suite of diagnostic programs, or test modules, that run on your system. These include diag

6 Introduction• Hard drives•CMOS • Parallel ports• Serial ports• PCI buses• Dell Remote Access Cards (DRAC 4 and DRAC 5)• USB controllers • Tape drive

Introduction 7• Diagnostic Test ResultsThis feature enables you to view the results of the diagnostic tests performed. See "Running Diagnostic Te

8 Introduction

Setting Up Diagnostics 9Setting up Dell PowerEdge DiagnosticsThis section describes the process for setting up Dell™ PowerEdge™ Diagnostics.Before You