Dell 3348 - PowerConnect Switch - Stackable Uživatelská příručka Strana 349
- Strana / 378
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Configuring Quality of Service 349
DSCP Mapping Page
The For the list of the DSCP default queue settings, contains the following fields:
NOTE: In a stacking configuration, Queue 4 is used for forwarding stacking traffic. Therefore,
assigning additional traffic to Queue 4 may interfere with stack control.
• DSCP In—Indicates the values of the DSCP field within the incoming packet.
• Queue—Indicates the queue to which packets with the specific DSCP value are
assigned. The values are 1-4, where one is the lowest and four is the highest value.
Mapping a DSCP value and assigning priority queue:
1 Open the DSCP Mapping page.
2 Select a value in the DSCP In column.
3 Define the Queue fields.
4 Click Apply Changes. The DSCP is not overwritten, and the value is assigned a
forwarding queue.
Assigning DSCP Values Using the CLI Commands
The following table summarizes the equivalent CLI commands for configuring fields in the
DSCP Mapping page.
- User’s Guide 1
- Notes, Notices, and Cautions 2
- Contents 3
- 5 Getting Started 6
- 8 Viewing Statistics 9
- 10 Getting Help 10
- Overview 11
- System Description 12
- Stack Members and Unit ID 13
- Configuration Handling 14
- Rearranging Stacks 15
- Replacing Stack Members 15
- 16 Overview 16
- Overview 17 17
- 18 Overview 18
- Hardware Description 19
- 20 Hardware Description 20
- PowerConnect 3324 Rear Panel 20
- PowerConnect 3348 Rear Panel 20
- Stacking LEDs 21
- Stack ID Button 21
- Mode Button 22
- Hardware Description 23 23
- Stacking Connections 23
- Ports Description 24
- LED Definitions 24
- System LEDs 25
- Port LEDs 26
- Installing the 29
- PowerConnect 29
- 3324/3348 Switch 29
- Installation Precautions 30
- Site Requirements 30
- Unpacking and Installation 31
- Device Rack Installation 32
- 3324/3348 devices or 33
- 3324/3348 stack 33
- Connecting Stacking Cables 33
- Connected Stack 34
- AC Power Connection 35
- Port Connections 36
- GigaPort Connector 37
- Cable Connections 38
- To connect the device: 39
- Configuring the 41
- Configuration Overview 42
- Auto-Negotiation 43
- Baud Rate 45
- Booting the Device 46
- Initial Configuration 49
- Default Gateway 51
- SNMP Community Strings 51
- Advanced Configuration 53
- Sample Configuration Process 60
- Device Default Settings 64
- Remote Management Access 65
- "Dell" 67
- Telnet access 70
- Web Access (HTTP server) 72
- Logging on Interface 73
- Password Prompt 74
- Configuring Stacking 75
- Rebooting the Device 76
- Startup Menu Functions 77
- Erasing the FLASH File 78
- Erasing FLASH Sectors 79
- Password Recovery 80
- Running Diagnostics 80
- Defining SNMP Settings 85
- Connecting Devices 86
- Getting Started 87
- Understanding the Interface 88
- Tree View 89
- Device View 90
- Device Representation 90
- Work Desk 91
- 92 Getting Started 92
- Information Buttons 93
- Help Button 94
- About Button 94
- Using the CLI 97
- Privileged EXEC Mode 98
- Global Configuration Mode 99
- Interface Configuration Mode 99
- Starting the CLI 100
- Telnet Connection 101
- 102 Getting Started 102
- Configuring System 103
- Information 103
- System Page 104
- Viewing the Asset Page 105
- Asset Page 106
- System Health Page 109
- Viewing the Versions Page 110
- Versions Page 111
- CLI Command Description 111
- Resetting the Device 112
- Managing Logs 113
- Logs Page 114
- Global Log Parameters Page 116
- Displaying RAM Log Table 118
- Displaying the Log File Table 121
- Defining Device IP Addresses 126
- Defining Default Gateways 127
- Defining IP Interfaces 130
- Defining DHCP IP Interfaces 133
- Configuring ARP 136
- 1 Open the ARP Settings page 137
- Managing Device Security 139
- Management Security Page 140
- Defining Access Profiles 141
- Add An Access Profile Page 143
- Authentication Profiles Page 149
- Select Authentication Page 152
- Local User Database Page 157
- ******* 157
- Defining Line Passwords 160
- Defining Enable Password 161
- RADIUS Settings Page 164
- Defining SNMP Parameters 168
- Defining Communities 169
- Defining Traps 171
- SNMP Trap Settings Page 172
- Managing Files 175
- File Management Overview 176
- Downloading Files 177
- Uploading Files 180
- Resetting the Active Image 182
- Copying and Deleting Files 183
- Copy Files Page 184
- Defining Advanced Settings 186
- General Settings Page 187
- Configuring Switch 189
- Configuring Network Security 190
- Network Security Overview 191
- Configuring Port Security 193
- Defining IP-Based ACLs 196
- Defining MAC-Based ACLs 200
- Add ACE to MAC Based ACL Page 201
- Binding ACLs 205
- ACL Bindings Page 206
- 1 Open the ACL Bindings page 206
- Configuring Ports 207
- Defining Port Parameters 208
- Port Configuration 209
- Defining LAG Parameters 216
- LAG Configuration Page 217
- Enabling Storm Control 222
- Port Mirroring Page 226
- Configuring Address Tables 229
- Defining Static Addresses 230
- Viewing Dynamic Addresses 233
- Configuring GARP 235
- Defining GARP Timers 236
- GARP Timers Page 237
- Defining STP Global Settings 240
- Defining STP Port Settings 244
- STP Port Settings Page 245
- Defining STP LAG Settings 248
- STP LAG Settings Page 249
- Configuring VLANs 254
- VLAN Page 255
- Defining VLAN Members 256
- VLAN Membership Section 257
- VLAN Port Membership Table 259
- Defining VLAN Ports Settings 261
- VLAN Port Settings Page 262
- Defining VLAN LAG Settings 264
- VLAN LAG Setting Page 265
- Configuring GVRP 267
- GVRP Parameters Page 269
- Aggregating Ports 272
- Defining LACP Parameters 274
- Global Parameters 275
- Port Parameters Table 276
- Defining LAG Membership 279
- Multicast Forwarding Support 280
- Multicast Support Page 281
- Bridge Multicast Group Page 284
- Enabling IGMP Snooping 289
- IGMP Snooping Page 290
- Viewing Statistics 293
- Viewing Tables 294
- Viewing Utilization Summary 295
- 296 Viewing Statistics 296
- Utilization Summary Page 296
- Viewing Counter Summary 297
- Viewing Interface Statistics 298
- Viewing Statistics 299 299
- Viewing Etherlike Statistics 301
- 302 Viewing Statistics 302
- Etherlike Statistics Page 302
- Viewing GVRP Statistics 304
- Viewing RMON Information 307
- 308 Viewing Statistics 308
- RMON Statistics Group Page 308
- Viewing Statistics 309 309
- Viewing Statistics 311 311
- RMON History Control Page 311
- 314 Viewing Statistics 314
- RMON History Table 314
- Defining Device Events 316
- Viewing Statistics 317 317
- RMON Events Control Page 317
- Viewing the Events Log 320
- Defining Device Alarms 321
- 322 Viewing Statistics 322
- RMON Alarm Page 322
- Viewing Statistics 323 323
- 1 Open the RMON Alarm page 323
- Viewing Charts 326
- Viewing Port Statistics 327
- 328 Viewing Statistics 328
- Port Statistics Page 328
- Viewing LAG Statistics 331
- 332 Viewing Statistics 332
- LAG Statistics Page 332
- 2 Select an interface type 332
- Configuring Quality of 335
- Quality of Service Page 336
- QoS Services 338
- QoS Global Parameters Page 339
- QoS Global Settings Page 340
- Interface Settings Page 342
- Defining Queue Settings 343
- Mapping to Queues 346
- Mapping DSCP Values to Queues 348
- UDP to Queue page 355
- Getting Help 357
- Technical Assistance 358
- AutoTech Service 359
- Problems With Your Order 360
- Product Information 360
- Before You Call 361
- Contacting Dell 361
Související produkty a manuály pro Software Dell 3348 - PowerConnect Switch - Stackable
Software Dell 735N Uživatelský manuál
(4 stránky)
(4 stránky)
Software Dell PowerVault 755N Technické informace
(156 stránky)
(156 stránky)
Software Dell Symantec Backup Exec Uživatelský manuál
(247 stránky)
(247 stránky)
Software Dell Data Protection Uživatelský manuál
(29 stránky)
(29 stránky)
Software Dell Wake-on-LAN Uživatelský manuál
(15 stránky)
(15 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce