Dell PowerEdge 2900 Uživatelská příručka

www.dell.com | support.dell.comDell™ SystemsTower-to-RackConversion Guidebook.book Page 1 Friday, May 26, 2006 3:03 PM

8 Tower-to-Rack Conversion GuideFigure 1-1. Tower-To-Rack Kit ContentsRecommended Tools and Supplies• #2 Phillips screwdriver• 3/8-inch or 10-mm nut d

Tower-to-Rack Conversion Guide 9• Installing the optional 1x2 flex bay bracket• Installing the shoulder nuts and plastic filler panels• Removing the r

10 Tower-to-Rack Conversion GuideFigure 1-2. Removing the Tower BezelPreparing the System for Conversion1 Turn off the system and attached peripherals

Tower-to-Rack Conversion Guide 11Removing the System Cover CAUTION: Any installation that requires removal of the system cover is intended solely to

12 Tower-to-Rack Conversion GuideFigure 1-3. Removing the Tower Components31256874111091 top panel 2 hex screw (top panel) 3 cover4 cover latch and re

Tower-to-Rack Conversion Guide 13Removing the Optional 1x2 Flex Bay BracketIf your system has the optional 1x2 flex bay, use the following procedure t

14 Tower-to-Rack Conversion GuideFigure 1-4. Removing the Control Panel Assembly1 control panel board (top view) 2 M3 x 5 T10 Torx panhead screw (3)3

Tower-to-Rack Conversion Guide 15Removing the Tower Front PlateUsing a T-10 Torx driver, remove the 29 screws that secure the tower front plate to the

16 Tower-to-Rack Conversion GuideFigure 1-6. Installing the Rack Front Plate and Rack Ears1 metal filler panel 2 chassis double wall 3 right rack ear4

Tower-to-Rack Conversion Guide 17Installing the Control Panel Assembly1Install the control panel assembly.aInsert the display module into the front pa

book.book Page 2 Friday, May 26, 2006 3:03 PM

18 Tower-to-Rack Conversion GuideFigure 1-7. Installing the Control Panel Assembly 1 M3 x 12 T10 Torx panhead screw (2)2 display module 3 display modu

Tower-to-Rack Conversion Guide 19Installing the Optional 1x2 Flex Bay Bracket NOTE: The rack front panel is keyed so that the 1x2 flex bay bracket in

20 Tower-to-Rack Conversion GuideInstalling the System Cover1Lift up on the cover latch. See Figure 1-3.2 Place the cover on top of the system and off

Tower-to-Rack Conversion Guide 21Figure 1-9. Installing the Shoulder NutsRemoving the Rack DoorsYou must remove the doors from the rack cabinet to pro

22 Tower-to-Rack Conversion GuideInstalling the Cable-Management ArmSee the procedures contained in the system Rack Installation Guide.Routing CablesS

Printed in China.Printed on recycled paper.book.book Page 1 Friday, May 26, 2006 3:03 PM

book.book Page 2 Friday, May 26, 2006 3:03 PM

www.dell.com | support.dell.comDell™ SystemsTower-to-RackConversion Guidebook.book Page 1 Friday, May 26, 2006 3:03 PM

Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates

Contents 3Contents CAUTION: Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . 5SAFETY: Rack Mounting of Systems . . . . . . .

4 Contentsbook.book Page 4 Friday, May 26, 2006 3:03 PM

Tower-to-Rack Conversion Guide 5 CAUTION: Safety InstructionsUse the following safety guidelines to help ensure your own personal safety and to help

6 Tower-to-Rack Conversion GuideGeneral Installation InstructionsThe system Rack Installation Guide provides instructions for trained service technici

Tower-to-Rack Conversion Guide 7Rack Stabilizer Feet CAUTION: Before installing systems in a rack, install front and side stabilizers on stand-alone