Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950) Uživatelský manuál stáhnout pdf (Strana 10)

Keyboard Controller failure

Faulty keyboard controller; faulty system board

See Getting Help.

Manufacturing mode detected

System is in manufacturing mode.

Reboot to take the system out of manufacturing mode.

MEMBIST failure - The following

DIMM/rank has been disabled by BIOS:

DIMM x Rank y

Faulty memory module(s).



See Troubleshooting System Memory.

Memory address line failure at

address, read value expecting value

Faulty or improperly installed memory modules.

See Troubleshooting System Memory.

Memory double word logic failure at

address, read value expecting value

Memory odd/even logic failure at

address, read value expecting value

Memory write/read failure at

address, read value expecting value

Memory tests terminated by

keystroke.

POST memory test terminated by pressing the

spacebar.

Information only.

No boot device available

Faulty or missing optical drive subsystem, hard

drive, or hard-drive subsystem, or no boot disk in

drive A.

Use a CD or hard drive. If the problem persists, see

Troubleshooting an Optical Drive and Troubleshooting a Hard

Drive. See Using the System Setup Program for information on

setting the order of boot devices.

No boot sector on hard drive

Incorrect configuration settings in System Setup

program, or no operating system on hard drive.

Check the hard-drive configuration settings in the System

Setup program. See Using the System Setup Program. If

necessary, install the operating system on your hard drive.

See your operating system documentation.

No timer tick interrupt

Faulty system board.

See "Getting Help."

Northbound merge error - The

following DIMM has been disabled by

BIOS: DIMM x

The specified DIMM was unable to establish a

successful data link with the memory controller.



See Troubleshooting System Memory.

PCIe Degraded Link Width Error:

Embedded Bus#nn/Dev#nn/Funcn

Expected Link Width is n

Actual Link Width is n

Faulty or improperly installed PCIe card in the

specified slot.

Reseat the PCIe card in the specified slot number. See

Expansion-Card Riser. If the problem persists, see Getting

Help.

PCIe Degraded Link Width Error: Slot

Expected Link Width is n

Actual Link Width is n

Faulty or improperly installed PCIe card in the

specified slot.

Reseat the PCIe card in the specified slot number. See

Expansion-Card Riser. If the problem persists, see Getting

Help.

PCIe Training Error: Embedded

Bus#nn/Dev#nn/Funcn

PCIeTrainingError:Slotn

Faulty or improperly installed PCIe card in the

specified slot.

Reseat the PCIe card in the specified slot number. See

Expansion-Card Riser. If the problem persists, see Getting

Help.

PCI BIOS failed to install

PCI device BIOS (Option ROM) checksum failure is

detected during shadowing.

Loose cables to expansion card(s); faulty or

improperly installed expansion card(s).

Reseat the expansion card(s). Ensure that all appropriate

cablesaresecurelyconnectedtotheexpansioncard(s).Ifthe

problem persists, see Troubleshooting Expansion Cards.

Plug & Play Configuration Error

Error encountered in initializing PCI device; faulty

system board.

Install the NVRAM_CLR jumper and reboot the system. See

Figure6-1 for jumper location. If the problem persists, see

Troubleshooting Expansion Cards.

Read fault

Requested sector not found

The operating system cannot read from the

diskette or hard drive, the system could not find a

particular sector on the disk, or the requested

sector is defective.

Replace the diskette. Ensure that the diskette and hard drive

cables are properly connected. See Troubleshooting

Expansion Cards, or Troubleshooting a Hard Drive for the

appropriate drive(s) installed in your system.

Remote configuration update attempt

failed

System unable to process Remote Configuration

request.

Retry Remote Configuration.

ROM bad checksum = address

Expansion card improperly installed or faulty.

Reseat the expansion card(s). Ensure that all appropriate

cables are securely connected to the expansion card(s). If the

problem persists, see Troubleshooting Expansion Cards.

Sector not found

Seek error

Seek operation failed

Faulty diskette or hard drive.

See Troubleshooting a Hard Drive for the appropriate drive(s)

installed in your system.

Shutdown failure

Shutdown test failure.

See Troubleshooting System Memory.

The amount of system memory has

changed

Memory has been added or removed or a memory

module may be faulty.

If memory has been added or removed, this message is

informative and can be ignored. If memory has not been

added or removed, check the SEL to determine if single-bit or

multi-bit errors were detected and replace the faulty memory

module. See Troubleshooting System Memory.

Time-of-day clock stopped

Faulty battery or faulty chip.

See Troubleshooting the System Battery.

The following DIMM pair is not

compatible with the memory

controller: DIMM x and DIMM y

The specified DIMM(s) are incompatible with the

system.

Ensure that only Dell-qualified memory is used. Dell

recommends purchasing memory upgrade kits directly from

www.dell.com or your Dell sales agent to ensure

compatibility.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 80 81

Komentáře k této Příručce

Žádné komentáře

Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950) Uživatelský manuál Strana 10

Komentáře k této Příručce

Související produkty a manuály pro Servery Dell Microsoft Windows Unified Data Storage Server 2003 (PowerVault NX 1950)