Dell Networking S6000 Uživatelský manuál stáhnout pdf (Strana 392)

100

101

Gi 13/8 (Up)

Gi 13/13 (Up)

Gi 13/14 (Up)

Dell#

The following example shows the port channel’s mode (L2 for Layer 2 and L3 for Layer 3 and L2L3 for a

Layer 2-port channel assigned to a routed VLAN), the status, and the number of interfaces belonging to

the port channel.

Dell>show interface port-channel 20

Port-channel 20 is up, line protocol is up

Hardware address is 00:01:e8:01:46:fa

Internet address is 1.1.120.1/24

MTU 1554 bytes, IP MTU 1500 bytes

LineSpeed 2000 Mbit

Members in this channel: Gi 9/10 Gi 9/17

ARP type: ARPA, ARP timeout 04:00:00

Last clearing of "show interface" counters 00:00:00

Queueing strategy: fifo

1212627 packets input, 1539872850 bytes

Input 1212448 IP Packets, 0 Vlans 0 MPLS

4857 64-byte pkts, 17570 over 64-byte pkts, 35209 over 127-byte pkts

69164 over 255-byte pkts, 143346 over 511-byte pkts, 942523 over 1023-byte

pkts

Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles

42 CRC, 0 IP Checksum, 0 overrun, 0 discarded

2456590833 packets output, 203958235255 bytes, 0 underruns

Output 1640 Multicasts, 56612 Broadcasts, 2456532581 Unicasts

2456590654 IP Packets, 0 Vlans, 0 MPLS

0 throttles, 0 discarded

Rate info (interval 5 minutes):

Input 00.01Mbits/sec, 2 packets/sec

Output 81.60Mbits/sec, 133658 packets/sec

Time since last interface status change: 04:31:57

Dell>

When more than one interface is added to a Layer 2-port channel, Dell Networking OS selects one of the

active interfaces in the port channel to be the primary port. The primary port replies to flooding and

sends protocol data units (PDUs). An asterisk in the show interfaces port-channel brief

command indicates the primary port.

As soon as a physical interface is added to a port channel, the properties of the port channel determine

the properties of the physical interface. The configuration and status of the port channel are also applied

to the physical interfaces within the port channel. For example, if the port channel is in Layer 2 mode, you

cannot add an IP address or a static MAC address to an interface that is part of that port channel. In the

following example, interface GigabitEthernet 1/6 is part of port channel 5, which is in Layer 2 mode, and

an error message appeared when an IP address was configured.

Dell(conf-if-portch)#show config

interface Port-channel 5

no ip address

switchport

channel-member GigabitEthernet 1/6

Dell(conf-if-portch)#int gi 1/6

Dell(conf-if)#ip address 10.56.4.4 /24

% Error: Port is part of a LAG Gi 1/6.

Dell(conf-if)#

392

Interfaces

1 2 ... 387 388 389 390 391 392 393 394 395 396 397 ... 985 986

Komentáře k této Příručce

Žádné komentáře

Dell Networking S6000 Uživatelský manuál Strana 392

Komentáře k této Příručce

Související produkty a manuály pro Software Dell Networking S6000