Dell Networking S6000 Uživatelský manuál stáhnout pdf (Strana 403)

100

101

When connected to a QSFP or QSFP+ port on a 40 Gigabit adapter, QSA acts as an interface for the SFP

or SFP+ cables. This interface enables you to directly plug in an SFP or SFP+ cable originating at a 10

Gigabit Ethernet port on a switch or server.

You can use QSFP optical cables (without a QSA) to split a 40 Gigabit port on a switch or a server into

four 10 Gigabit ports. You must enable the fan-out mode in order for this mechanism to work. For more

details, see Splitting QSFP Ports to SFP+ Ports.

Similarly, you can enable the fan-out mode to configure the QSFP port on a device to act as an SFP or

SFP+ port. As the QSA enables a QSFP or QSFP+ port to be used as an SFP or SFP+ port, Dell Networking

OS does not immediately detect the QSA after you insert it into a QSFP port cage.

After you insert an SFP or SFP+ cable into a QSA connected to a 40 Gigabit port, Dell Networking OS

assumes that all the four fanned-out 10 Gigabit ports have plugged-in SFP or SFP+ optical cables.

However, the link UP event happens only for the first 10 Gigabit port and you can use only that port for

data transfer. As a result, only the first fanned-out port is identified as the active 10 Gigabit port with a

speed of 10G or 1G depending on whether you insert an SFP+ or SFP cable respectively.

NOTE: Although it is possible to configure the remaining three 10 Gigabit ports, the Link UP event

does not occur for these ports leaving the lanes unusable. Dell Networking OS perceives these ports

to be in a Link Down state. You must not try to use these remaining three 10 Gigabit ports for actual

data transfer or for any other related configurations.

NOTE: Trident2 chip sets do not work at 1G speeds with auto-negotiation enabled. As a result,

when you peer any device using SFP, the link does not come up if auto-negotiation is enabled.

Therefore, you must disable auto-negotiation on platforms that currently use Trident2 chip sets

(S6000 and Z9000). This limitation applies only when you convert QSFP to SFP using the QSA. This

constraint does not apply for QSFP to SFP+ conversions using the QSA.

Important Points to Remember

• Before using the QSA to convert a 40 Gigabit Ethernet port to a 10 Gigabit SFP or SFP+ port, you must

enable 40 G to 4*10 fan-out mode on the device.

• When you insert a QSA into a 40 Gigabit port, you can use only the first 10 Gigabit port in the fan-out

mode to plug-in SFP or SFP+ cables. The remaining three 10 Gigabit ports are perceived to be in Link

Down state and are unusable.

• You cannot use QSFP optical cables in a QSA setup.

• When you remove the QSA module alone from a 40 Gigabit port, without connecting any SFP or SFP

+ cables; Dell Networking OS does not generate any event. However, when you remove a QSA

module that has SFP or SFP+ optical cables plugged in, Dell Networking OS generates a SFP or SFP+

Removed event.

• In the S6000 platform, you can use the QSA on any of the ports. However, the existing maximum fan-

out restrictions apply to the ports.

• The QSA module does not have a designated EEPROM. To recognize a QSA, Dell Networking OS

reads the EEPROM corresponding to a SFP+ or SFP module that is plugged into QSA. The access

location of this EEPROM is different from the EEPROM location of the QSFP+ module.

• The diagnostics application is capable of detecting insertion or removal of both the QSA as well as the

SFP+ or SFP optical cables plugged into the QSA. In addition, the diagnostic application is also

capable of reading the DDS and Vendor information from the EEPROM corresponding to SFP+ or SFP

optical cables. As a result, no separate detection of QSA is required.

Interfaces

403

1 2 ... 398 399 400 401 402 403 404 405 406 407 408 ... 985 986

Komentáře k této Příručce

Žádné komentáře

Dell Networking S6000 Uživatelský manuál Strana 403

Komentáře k této Příručce

Související produkty a manuály pro Software Dell Networking S6000